Laserfiche WebLink
GSM "L" FLASHING <br />PRE -MADE GSM EDGE FLASHING <br />11 <br />DOOR PAN FLASHING <br />6 CEMCO # 66 EXPANDED FLANGE <br />CEMCO #7 EXTENDED FOUNDATION <br />SCREED WITH 1-1/2" EXTENSION <br />CEMCO # 66 EXPANDED FLANGE <br />I <br />I <br />I <br />8 <br />3-COAT STUCCO SYSTEM AD 51 <br />0/ METAL LATH <br />CORNER <br />SHOP SOLDER ALL JOINTS/CUTS <br />CASING BEAD. APPLY 0/ W.R.B. <br />CASING BEAD <br />INTEGRAL STUCCO SCREED BEYOND <br />O5 CEMCO #7 EXTENDED FOUNDATION <br />-SCREED WITH 1-1/2" EXTENSIO, <br />IMPERVIOUS SURFACE STOP, HEIGHT <br />"L" <br />1NALL <br />EXTEND 1" PAST GSM FLASHING <br />TO TOP OF IMPERVIOUS SURFACE <br />�� <br />3 <br />r\�4 GSM 1" FLASHING <br />J� <br />Pam' <br />8 I'� <br />, <br />IMPERVIOUS SURFACE, OVERLAP <br />����� <br />o <br />` <br />SEAM PAPER <br />LATH ON THE FLASHING TO THE EDGE <br />OF THE DECK SURFACE <br />WALL FLASHING <br />B <br />_ SUBSTRATE <br />\3 <br />GSM DECK EDGE LAP WHERE <br />OCCURS <br />GSM EDGE FLASHING <br />I <br />N SLOPE <br />SEE STRAIGHT LAP BELOW FOR <br />l I� <br />L <br />/ ADDITIONAL INFO. <br />IMPERVIOUS <br />\\-- <br />_ _ = <br />SURFACE <br />PRE -MADE CORNER <br />3 BEDS OF SEALANT 1" APART <br />\ / I \ / <br />20 <br />1 20 <br />SECTION A7 <br />SEE SCUPPER DETAIL <br />SADDLE FLASHING <br />SADDLE FLASHING <br />ONE PIECE SOLDERED SADDLE <br />s21 <br />FLASHING <br />��� ' S.A.F. <br />�, <br />W.R.B. <br />Q2 <br />12 3 15 10 <br />EDGE MOUNTED LATH POST DECK EDGE EXT. GRADE <br />RAIL FLASHING METAL PLYWOOD <br />DECK SURFACE y ' A <br />I <br />J <br />I <br />/8' <br />INTEGRAL STUCCO SCREED <br />C.0 <br />LAPPED GSM EDGE FLASHING <br />3 BEDS OF SEALANT 1" APART <br />sG�s <br />I J <br />CONTINUOUS BEAD OF SEALANT <br />d <br />4 <br />AT OVERLAP SEAM <br />GSM EDGE FLASHING <br />I <br />1 DECK SHEATHING <br />' ���' <br />PROFILE SECTION AT DECK SIDE <br />OF SCUPPER <br />STRAIGHT LAP <br />11 <br />i <br />DOOR PAN FLASHING <br />i <br />WAIL <br />NOTE: ALL FLASHING SEAMS AND LAPS SHALL BE INSTALLED AS TO NOT BUCK WATER. <br />- <br />SADDLE FLASHING <br />GSM 1" FLASHING LAPPED OVER <br />CEMCO #7 EXTENDED FOUNDATION <br />S.A.F. <br />SCUPPER <br />SCREED WITH 1-1/2" EXTENSION <br />GSM EDGE FLASHING <br />SCUPPER (DECK SIDE) <br />PARALLEL W/ IMPERVIOUS SURFACE <br />IMPERVIOUS SURFACE <br />SLOPED PLYWOOD FEATHER PLYWOOD EDGE <br />CONTINUOUS BEAD OF SEALANT AT <br />EXT. GRADE PLYWOOD <br />CRICKET, TYPICAL FLUSH WITH HORIZONTAL <br />DECK EDGE PERPENDICULAR TO WALL <br />OVERLAP SEAM <br />3 BEDS OF SEALANT 1" APART <br />PRE-TREATMENT 0/ BASE COAT 0/ <br />SURFACE TYPICAL AT ALL <br />EXPOSED LOCATIONS <br />INTEGRAL STUCCO SCREED 3 SIDES. <br />GSM DECK EDGE METAL <br />SEE PROFILE SECTION <br />GSM "L" FLASHING <br />SEALANT AT JOINT A <br />N <br />SUBSTRATE <br />RUN METAL LATH TO EDGE OF THE <br />DECK EDGE METAL <br />a LU a <br />IMPERVIOUS SURFACE <br />PRE-TREATMENT 0/ BASE COAT 0/ <br />"L" <br />IMPERVIOUS — <br />SURFACE STOP, <br />SLOPE <br />4' EDGE METAL STOP HEIGHT 1/8" TO <br />0 0 <br />m m <br />SUBSTRATE <br />PRE-TREATMENT 0/ BASE COAT 0/ <br />GSM FLASHING 3" MIN. ABOVE <br />,% FOUNDATION SCREED FLASHING <br />HEIGHT TO TOP OF <br />3/16 <br />U) U) <br />SLOPE GSM DECK EDGE METAL <br />I <br />SADDLE FLASHING <br />IMPERVIOUS T <br />— 1x2 WOOD NAILER <br />SURFACE <br />N GSM DECK EDGE METAL 0/ <br />3 COAT STUCCO SYSTEM 0/ METAL <br />HORIZONTAL S.A.F. AND 0/ VERTICAL <br />SADDLE FLASHING <br />I LATH 0/ W.R.B. 0/ S.A.F. 0/ CEMCO #7 <br />CASING BEAD <br />SUBSTRATE 4S° SUBSTRATE SUBSTRATE 10" MIN. SUBSTRATE <br />GSM DECK EDGE METAL <br />�J \ <br />�� � <br />� i 3-COAT STUCCO SYSTEM 0/ METAL <br />E E <br />SLOPE SLOPSLOPE SLOP <br />IMPERVIOUS SURFACE, OVERLAP <br />LATH 0/ W.R.B. <br />CEMCO # 66 EXPANDED FLANGE <br />/ LATH ON THE FLASHING TO THE EDGE <br />SUBSTRATE <br />l <br />li CEMCO # 66 EXPANDED FLANGE <br />CASING BEAD 0/ W.R.B. 0/ SADDLE <br />FLASHING 0/ S.A.F. <br />N OF THE DECK SURFACE <br />SLOPE <br />CASING BEAD 0/ W.R.B. 0/ S.A.F. <br />1" MIN. <br />MAXIMUM SPAN BETWEEN 2 SCUPPERS / DRAINS IS <br />3-COAT STUCCO SYSTEM 0/ METAL <br />% CEMCO #7 EXTENDED FOUNDATION <br />r W.R.B. 0/ S.A.F. 0/ SOFFIT DRIP EDGE <br />M 6 FOOT MAXIMUSP N THE LESSER OF 12 FEET 6 OOT MAXIMUM SPAN <br />ROM WALL TO SCUPP F OM WALL TO DRAIN <br />LATH 0/ W.R.B. <br />SCREED WITH 1-1/2" EXTENSION <br />TEFL <br />or <br />2 TIMES THE DEPTH OF THE DECK <br />PARALLEL W/ IMPERVIOUS SURFACE <br />,- <br />,, <br />SHEATHING MAY OCCUR <br />W.R.B. 0/ S.A.F. 0/ SOFFIT DRIP <br />EDGE <br />��E� <br />�Q <br />4 ��� <br />____------ CEMCO # 12 SOFFIT DRIP EDGE <br />SCUPPER 14 8 WALL FLASHING DECK DRAIN 16 FACE OF EXTERIOR <br />- <br />FINISH <br />I <br />_ CEMCO # 12 SOFFIT DRIP EDGE, <br />EXTEND 1" PAST OPENING WHEN <br />APPLY SEALANT AFTER COMPLETION <br />OF IMPERVIOUS SURFACE SYSTEM <br />FINISH COAT <br />N ,\ s <br />- vQQEFL �� <br />E�S�' �p�� �-Ay <br />�� `r�o �``� <br />EXTEND 1"PAST OPENING WHEN <br />DECK EDGE IS FLUSH WITH WALL <br />BEYOND. <br />DECK EDGE IS FLUSH WITH WALL <br />O�`�`�` �PQ <br />REMOVABLE SOFFIT <br />3-COAT STUCCO CEILING SOFFIT 0/ <br />NOTES: IMPERVIOUS SURFACE TO REMAIN A MINIMUM OF 2" BELOW THE PERIMETER WEEP SCREED. <br />BEYOND <br />ROOF DECK DRAINAGE, INCLUDING SECONDARY DRAINS, SHALL COMPLY WITH CBC SECTION 1503 AND THE CALIFORNIA PLUMBING CODE. <br />SECTION A <br />SECTION B <br />SEE SCUPPER DETAIL. FOR ADDITIONAL INFORMATION SEE DETAILS <br />2 8 <br />VENT <br />FOR ADDITIONAL INFORMATION SEE <br />EXPANDED METAL LATH <br />DETAILS 2 20 <br />1 <br />FOR ADDITIONAL REQUIREMENTS AND INFORMATION SEE DETAILS <br />FOR ADDITIONAL INFO. ON SECTION A SEE DETAIL 10 FOR ADDITIONAL INFO. ON SECTION B <br />SEE DETAIL 8 FOR ADDITIONAL REQUIREMENTS AND INFO. SEE DETAIL 2 <br />- - <br />- - <br />SCUPPER TIE-IN <br />14 <br />DECK EDGE METAL <br />10 <br />sG�s <br />s�o-o <br />BUILD UP BASE COAT CRICKET WITH <br />SADDLE FLASHING <br />9T <br />F F` <br />1/4" RISE ON UP SLOPE SIDE <br />PLI-DEK SEAM PAPER TO COVER EXT. <br />WALL ASSEMBLY BEYOND <br />PLYWOOD PANEL EDGE /JOINTS <br />6 CEMCO # 66 EXPANDED FLANGE <br />WAIL <br />0 <br />2 PIECE "C" SHAPED GSM "L" <br />CASING BEAD, APPLY 0/ W.R.B. <br />GSM "L" FLASHING <br />FLASHING OVERLAP ASSEMBLY IN <br />THE DIRECTION OF SLOPE <br />"C" SHAPE SHALL BE PRE -MADE AND <br />SOLDERED <br />INTERIOR FINISH FLOOR <br />�P P <br />IJN� <br />JN0 1 1 <br />� <br />OFFSET METAL LATH EDGES <br />6" MIN. FROM EXT. <br />PLYWOOD SEAMS. <br />DOOR AND THRESHOLD ASSEMBLY <br />NOTE: <br />PER DOOR SCHEDULE <br />OVERLAP LATH 3/4" MINIMUM <br />FLASHING SEAMS AND LAPS SHALL BE INSTALLED AS TO NOT BUCK WATER, SEE DETAIL <br />= <br />CEMCO #7 EXTENDED FOUNDATION <br />SCREED WITH 1-1/2" EXTENSION <br />"WALL FLASHING" FOR TYPICAL REQUIREMENTS AT LAP. <br />APPLY JOINT SEALANT AFTER <br />COMPLETION OF IMPERVIOUS <br />5 CEMCO #7 EXTENDED FOUNDATION <br />SURFACE SYSTEM FINISH COAT AND <br />SCREED WITH 1-1/2" EXTENSION, <br />i <br />POST <br />3-COAT STUCCO SYSTEM 0/METAL <br />PRIOR TO DOOR THRESHOLD <br />EXTEND 1" PAST GSM 1" FLASHING <br />(PER PLAN) <br />LATH 0/ W.R.B. <br />INSTALLATION <br />4 GSM 1" FLASHING <br />� � � i <br />GSM "L" i i <br />W.R.B. 0/ S.A.F. 0/ FOUNDATION <br />PRE-TREATMENT 0/ BASE COAT 0/ <br />FLASHING �� <br />SCREED FLASHING <br />GSM 1 PIECE DOOR FLASHING PAN <br />4' 3 PRE -MADE CORNER GSM EDGE <br />CEMCO #7 EXTENDED FOUNDATION <br />°� <br />FLASHING <br />l li <br />SCREED WITH 1-1/2" EXTENSION <br />X <br />3 <br />c0 �� <br />3 BEDS OF SEALANT 1 APART TO <br />SEALANT TO OOZE OUT AND <br />i BUTTERED AT JOINT <br />_ <br />I I <br />PARALLEL W/ IMPERVIOUS SURFACE <br />Q <br />N <br />GSM 1 PIECE DOOR <br />FLASHING PAN AD 52 <br />ih <br />ih <br />APPLY JOINT SEALANT AFTER <br />SUBSTRATE <br />RECEIVE "L" FLASHING <br />i <br />PRE -MADE CORNER GSM EDGE <br />COMPLETION OF IMPERVIOUS <br />SLOPE <br />3' <br />FLASHING <br />SURFACE SYSTEM FINISH COAT <br />�� <br />- EXT. PLYWOOD PANEL EDGE / JOINT, <br />i L <br />_ <br />IMPERVIOUS SURFACE <br />�o�� <br />TYPICAL <br />2 ONE PIECE SOLDERED SADDLE <br />%DECK SURFACE <br />e� <br />o o <br />PRE-TREATMENT 0/ BASE COAT 0/ <br />GSM "L" FLASHING <br />�' <br />STAPLE 1-1/2" O.C. ON OVERLAPPED <br />LATH SEAMS <br />FLASHING <br />5�� 5�0 <br />o <br />- <br />4" INIMUM IMPERVIOUS SURFACE <br />LAPPED GSM 1" FLASHING <br />3 BEDS OF SEALANT 1"APART TO <br />\��\ \ <br />POST BASE PER <br />EXT. GRADE PLYWOOD <br />3 BEDS OF SEALANT 1"APART <br />STAPLE 2" O.C. AROUND PERIMETER <br />W `� RECEIVE CORNER DECK EDGE <br />ALL <br />\ <br />STRUCTURAL, GSM "L" 4" <br />CONTINUOUS BEAD OF SEALANT AT <br />`eQ FLASHING <br />oe�`' <br />" <br />FLASHING SHALL LIE <br />VERTICALLY FLAT <br />FLOOR JOIST OR BLOCKING - <br />INTERIOR <br />EXTERIOR <br />OVERLAP SEAM <br />J05 <br />AGAINST THE POST AND <br />CONNECTION POST PER STRUCT. <br />WALL EDGE LAP GSM "L" FLASHING NOTE: REFERENCE PLI-DEK SPECIFICATIONS FOR PROPER LATH INSTALLATION. <br />1 DECK SHEATHING <br />\�� <br />�\ <br />POST BASE <br />FOR ADDITIONAL REQUIREMENTS AND INFORMATION SEE DETAIL <br />2 <br />2 <br />FOR ADDITIONAL REQUIREMENTS AND INFORMATION SEE DETAIL <br />NOTE: ALL FLASHING SEAMS AND LAPS SHALL BE INSTALLED AS TO NOT BUCK WATER. 1 <br />FOR ADDITIONAL REQUIREMENTS AND INFORMATION SEE DETAILS <br />DECK EDGE PROTRUDING BEYOND EXTERIOR WALL <br />SHEATHING MAY OCCUR - <br />3 <br />POST FLASHING <br />15 <br />DOOR PAN FLASHING <br />11 <br />3-COAT STUCCO SYSTEM 0/ METAL <br />16 GA. STAINLESS STEEL SNAP IN <br />LATH 0/ W.R.B. <br />6 CEMCO # 66 EXPANDED FLANGE <br />COVER <br />I 2x SOLID BACKING REQUIRED BEHIND <br />CASING BEAD, APPLY 0/ W.R.B. <br />SEALANT JOINT AROUND DRAIN <br />S.A.F. WHEN SHEATHING NOT <br />I <br />PRIOR TO FINISH COAT <br />I PROVIDED <br />5 CEMCO #7 EXTENDED FOUNDATION <br />WALL �Pl <br />p� <br />I <br />I GSM 1" FLASHING <br />SCREED WITH 1-1/2" EXTENSION, <br />GSM 1" FLASHING <br />I l <br />W.R.B. 0/ S.A.F. 0/ FOUNDATION <br />EXTEND 1" PAST GSM 1" FLASHING <br />9- <br />I <br />SCREED FLASHING 0/ GSM 1"GALVANIZED, <br />/ SADDLE FLASHING <br />GALVANIZED,BONDERIZED DRAIN <br />DECK PLATE <br />I FLASHING <br />F, <br />� �1 FLASHING 4 GSM 1" FLASHING <br />CEMCO #7 EXTENDED FOUNDATION <br />y <br />O %L <br />�9�ti <br />I CEMCO #7 EXTENDED FOUNDATION <br />I li SCREED WITH 1-1/2" EXTENSION <br />WITH 1-1/2" EXTENSION <br />PARALLEL W/ IMPERVIOUS SURFACE <br />REMOVABLE DRAIN CAP <br />MADE CORNER GSM EDGE <br />GSM EDGE FLASHING <br />2 COAT ELASTOMERIC FINISH (GU80 <br />TOP COAT AND GS88 PIGMENTED <br />APPLY SEALANT AFTER COMPLETION <br />SUBSTRATE OF IMPERVIOUS SURFACE SYSTEM <br />I�PRE <br />SEALER) <br />FLASHING <br />iv SLOPE FINISH COAT <br />60 MIL, 2-COAT PD RESIN FIELD <br />DECK SURFACE P�� <br />� <br />PRE-TREATMENT 0/ REINFORCED <br />IMPERVIOUS SURFACE. OVERLAP <br />��4" <br />� <br />���� <br />BASE COAT <br />3 BEDS OF SEALANT 1" APART <br />��oe� <br />LATH ON THE FLASHING TO THE EDGE <br />\ <br />OF THE DECK SURFACE <br />LATH <br />4" <br />� <br />PRE-TREATMENT 0/ REINFORCED <br />� � � <br />BASE COAT 0/GSM "L" FLASHING 3" <br />o <br />DECK DRAIN PLATE <br />MIN. ABOVE FOUNDATION SCREED <br />FLASHING <br />2 ONE PIECE SOLDERED SADDLE <br />FLASHING <br />�� <br />2" OR 3" <br />EXT. GRADE PLYWOOD <br />BRONZE NO HUB ADAPTER <br />SWEAT -SOLDERED TO PLATE <br />WALL s� <br />DECK EDGE FLUSH WITH EXTERIOR WALL <br />5� <br />DRAIN MANUFACTURER - THUNDERBIRD PRODUCTS, 800-658-2743, THUNDERBIRDPRODUCTS.COM <br />REMOVABLE SOFFIT VENT <br />FOR 2" DRAIN- PRODUCT BD2NH-B <br />— DECK SHEATHING <br />(NOT SHOWN IN DETAIL 1 ) <br />FOR 3" DRAIN- PRODUCT BD3NH-B <br />FOR ADDITIONAL REQUIREMENTS AND INFORMATION SEE DETAILS 2 1 <br />FOR ADDITIONAL REQUIREMENTS AND INFORMATION SEE DETAILS 2 <br />SADDLE FLASHING ASSEMBLY (WALL FLASHING TO DECK EDGE METAL) <br />20 <br />DECK DRAIN <br />16 <br />- <br />12 <br />DECK TO WALL FLASHING <br />8 <br />- <br />4 <br />Architecture + Planning <br />17911 Von Karman Ave. <br />Suite 200 <br />Irvine, CA 92614 <br />ktgy.com <br />949.851.2133 <br />KTGY Project No: 2017-0934 <br />Project Contact: Debbie Holland <br />Email: dholland@ktgy.com <br />Principal: Wil Wong <br />Project Designer: D. Schoolmeester <br />Project Director: Debbie Holland <br />Developer <br />ED7 OAK <br />INVESTMENTS <br />S <br />4199 CAMPUS DRIVE <br />IRVINE, CA 92612 <br />PHONE NO. (714) 342-2502 <br />TF <br />No. <br />O <br />Q <br />U <br />Q <br />z <br />Q <br />Q <br />z <br />Q <br />U) <br />I- <br />w <br />w <br />U) <br />F_ <br />ICT <br />LO <br />T_ <br />L0 <br />015 <br />T_ <br />Nt <br />Date Description <br />It is the clients responsibility prior to or during construction to notify the architect in writing <br />of any perceived errors or omissions in the plans and specifications of which a contractor <br />thoroughly knowledgeable with the building codes and methods of construction should <br />reasonably be aware. Written instructions addressing such perceived errors or omissions <br />shall be received from the architect prior to the client or clients subcontractors proceeding <br />with the work. The client will be responsible for any defects in construction if these <br />procedures are not followed. <br />C, ARrc <br />No. C29795 <br />RENEWAL DATE <br />AUGUST 31, 2023 <br />s�9TF <br />�F CAS\ <br />License Stamp <br />EXTERIOR <br />IMPERVIOUS <br />SURFACE (PLI-DEK) <br />AD-55 <br />N <br />C) <br />CN <br />MU <br />COPYRIGHT (� <br />