|
NOTES:
<br />1. INTAKE DOOR AND TRIM SHALL BE REMOVED FOR DOOR MAINTENANCE.
<br />2. BOTTOM HINGED DOORS ARE SELF -CLOSING, NOISELESS, AND SELF -LATCHING. UL CLASSIFIED 90 MINUTE
<br />FIRE -RATED DOOR AND FRAME ASSEMBLY AND A TEMPERATURE RISE OF 250* F MAX IN 30 MINUTES.
<br />3. MAX OPENING FOR INTAKE DOOR IS 14" FROM FACE OF FINISHED WALL.
<br />4. 2019 CBC - 11 B-404.3.5 HEIGHT: CONTROLS AND OPERATING MECHANISMS SHALL BE LOCATED NO HIGHER
<br />THAN 48 INCHES, AND NO LOWER THAN 15 INCHES ABOVE THE FINISHED FLOOR MEASURED TO THE
<br />CENTER OF THE GRIP.
<br />5. 2019 CBC - 11 B-309.4 OPERATION: CONTROLS AND OPERATING MECHANISMS SHALL BE OPERABLE WITH ONE
<br />HAND AND SHALL NOT REQUIRE TIGHT GRASPING, PINCHING, OR TWISTING OF THE WRIST. THE FORCE
<br />REQUIRED TO ACTIVATE CONTROLS AND OPERATING MECHANISMS SHALL BE NO GREATER THAN 5
<br />POUNDS.
<br />1�
<br />r � �
<br />I I
<br />I I
<br />I I
<br />I I
<br />(WITHOUT TRIM)
<br />MECH BOX
<br />COVERTOP
<br />4 5.
<br />'"
<br />PLAN VIEW
<br />CHUTE INTAKE DOOR
<br />% GROUND & 8-21 FLOORS
<br />NOTES:
<br />1. CHUTE SHAFT SHALL NOT BE ERECTED UNTIL CHUTE HAS BEEN INSTALLED. FOR SOUND
<br />PROOFING PURPOSES, DOUBLE STUD -WALLS ARE REQUIRED ADJACENT TO OCCUPIED
<br />SPACES. INTERIOR OF SHAFT SHALL BE TAPED TO PREVENT ODOROUS AIR LEAKING INTO
<br />OCCUPIED SPACES.
<br />2. INTAKE DOOR NOT SHOWN FOR CLARITY.
<br />2HR FIRE -RATED WALL_
<br />PER SCHEDULE (S.A.D.)
<br />TAPE INTERIOR OF CHUTE SHAFT_
<br />TO PREVENT ODOROUS AIR LEAKS
<br />A36 FLOOR SUPPORT
<br />FRAME, SEE PLAN
<br />LIGHT RED OPEN
<br />(WHEN IN USE) BUTTON
<br />ELEVATION VIEW
<br />El BOX-
<br />15x18 BOTTOM HINGED, NORMALLY CLOSED
<br />LOW -VOLTAGE ELECTRICALLY INTERLOCKED,
<br />AUTOMATIC OPENING INTAKE DOOR
<br />hj
<br />SATIN CHROME PULL
<br />HANDLE W/ THUMB LATCH
<br />23" FROM
<br />F.O. WALL
<br />I
<br />2HR FIRE -RATED WALL
<br />I
<br />PER SCHEDULE (S.A.D.)
<br />I I
<br />I
<br />COAT CHUTE W/ SOUNDCOAT GP-1 OR KINETICS
<br />KDC-E-162; MATCH THICKNESS OF METAL
<br />I
<br />I I
<br />ANCHOR BOLTS W/ NEOPRENE GROMMETS.
<br />r-PROVIDE
<br />ON BRA RED SOUND ISOLATION
<br />PADS BELOW
<br />I I
<br />DISCHARGE LEVEL
<br />4._6.
<br />S CHUTE AIR AND SOUND ISOLATION
<br />NOTES:
<br />1. REFER TO MANUFACTURER SPECIFICATIONS FOR ALL OTHER INFORMATION NOT LISTED.
<br />$ FLOOR FRAME ANCHORING
<br />ANCHORING
<br />WILKINSON TYPE -A, B-LABEL CONSTRUCTION 90 MINUTE
<br />FIRE -RATED, ROLLING FIRE ENCLOSURE DOOR W/ 165" F.
<br />FUSIBLE LINK, SHOWN IN CLOSED POSITION
<br />NOTES:
<br />1. INTAKE DOOR AND TRIM SHALL BE REMOVED FOR DOOR MAINTENANCE.
<br />2. SIDE HINGED DOORS ARE SELF -CLOSING, NOISELESS, AND SELF -LATCHING. UL CLASSIFIED 90 MINUTE FIRE -RATED
<br />DOOR AND FRAME ASSEMBLY AND A TEMPERATURE RISE OF 250' F MAX IN 30 MINUTES.
<br />3. 2019 CBC - 11B-404.3.5 HEIGHT: CONTROLS AND OPERATING MECHANISMS SHALL BE LOCATED NO HIGHER THAN 48
<br />INCHES, AND NO LOWER THAN 15 INCHES ABOVE THE FINISHED FLOOR MEASURED TO THE CENTER OF THE GRIP.
<br />4. 2019 CBC - 11 B-309.4 OPERATION: CONTROLS AND OPERATING MECHANISMS SHALL BE OPERABLE WITH ONE HAND
<br />AND SHALL NOT REQUIRE TIGHT GRASPING, PINCHING, OR TWISTING OF THE WRIST. THE FORCE REQUIRED TO
<br />ACTIVATE CONTROLS AND OPERATING MECHANISMS SHALL BE NO GREATER THAN 5 POUNDS.
<br />30° (fy')
<br />r
<br />I THRU-WALL
<br />-
<br />I
<br />Ie'
<br />ROUGH
<br />OPENING
<br />ELEVATION VIEW PLAN VIEW
<br />(WITHOUT TRIM)
<br />18x18 SIDE HINGED, AUTOMATIC OPENING
<br />ELECTRICALLY INTERLOCKED INTAKE DOOR
<br />A
<br />J
<br />RED OPEN SATIN CHROME PULL
<br />BUTTON HANDLE W/ THUMB LATCH
<br />THRU-WALL INTAKE DOOR
<br />SCALE: %8" = V-0" 2 FLOOR 1
<br />NOTES:
<br />1. PROVIDE HIGH PRESSURE CHUTE WASHDOWN NOZZLE.
<br />2. FILL SANITATION TANK WITH CONCENTRATED DISINFECTING SOLUTION. THE SYPHON HOSE SHOULD REACH THE BOTTOM
<br />OF THE SOLUTION CONTAINER. TO FLUSH WITH CLEAR WATER, TURN HANDLE TO THE ON POSITION. FACTORY SETTING OF
<br />THE PROPORTIONING VALVE IS FOR 50-GALLONS PER GALLON OF DISINFECTING SOLUTION.
<br />3. NOTE THAT THE ACCESS DOOR AND D & S UNIT ARE SHOWN OUTSIDE OF CHUTE SHAFT FOR CLARITY. ALL WASHDOWN
<br />EQUIPMENT WILL BE INSTALLED WITHIN CHUTE SHAFT, ABOVE THE HIGHEST INTAKE. (1) D & S UNIT PER CHUTE.
<br />4. 2019 CBC - 11 B-404.3.5 HEIGHT: CONTROLS AND OPERATING MECHANISMS SHALL BE LOCATED NO HIGHER THAN 48 INCHES
<br />AND NO LOWER THAN 15 INCHES ABOVE THE FINISHED FLOOR MEASURED TO THE CENTER OF THE GRIP.
<br />5. 2019 CBC - 11 B-309.4 OPERATION: CONTROLS AND OPERATING MECHANISMS SHALL BE OPERABLE WITH ONE HAND AND
<br />SHALL NOT REQUIRE TIGHT GRASPING, PINCHING, OR TWISTING OF THE WRIST. THE FORCE REQUIRED TO ACTIVATE
<br />CONTROLS AND OPERATING MECHANISMS SHALL BE NO GREATER THAN 5 POUNDS.
<br />6. SUPPLIED BY VENDOR - INSTALLED BY PLUMBER.
<br />PLUMBING SCHEMATIC LEGEND:
<br />1. 3/4"0 DOMESTIC HOT WATER INLET WITH VACUUM BREAKER.
<br />2. QUARTER -TURN GATE VALVE (SHUT-OFF AND BYPASS), (2) TOTAL.
<br />3. PLUMBING DESIGN, MATERIALS, AND INSTALLATION BY OTHERS.
<br />4. 24-VDC SOLENOID VALVE (OPTIONAL). NOT NEEDED FOR MANUAL OPERATION.
<br />5. D & S UNIT: 1-GALLON CONTAINER, MOUNTING BRACKET, AND PROPORTIONAL
<br />VALVE AT REMOTE LOCATION.
<br />6. FLUSHING SPRAY HEAD BELOW CHUTE VENT.
<br />7. FIRE SPRINKLER HEAD AT HIGHEST INTAKE, LOWEST INTAKE, AND EVERY OTHER
<br />FLOOR BETWEEN - CONNECTION BY OTHERS.
<br />8. SIDE -HINGED, UL RATED 90 MINUTE B-LABEL ACCESS DOOR.
<br />9. SATIN CHROME PULL -HANDLE.
<br />G FIRE SPRINKLER DETAILS AND CHUTE SANITATION UNIT
<br />SCALE:3/8"= t'-o^ v AT HIGHEST INTAKE
<br />SHEET NOTES: 30" 0 CHUTE DETAILS
<br />1. CHUTE MATERIAL: GALVANIZED STEEL.
<br />2. ALL WALL ASSEMBLIES ENCASING THE CHUTE SHAFT SHALL BE 2HR FIRE -RATED.
<br />3. SEE ARCHITECTURAL AND/OR STRUCTURAL DRAWINGS TO VERIFY ALL
<br />INFORMATION NOT RELATED TO ATM'S SCOPE OF WORK PER AGREEMENT.
<br />4. POUR RINGS WILL VARY BASED ON THICKNESS OF FLOOR SLAB AND SHALL BE
<br />PROVIDED BY MANUFACTURER.
<br />GENERAL NOTES:
<br />1. ANY DESIGNS OR SOLUTIONS SHOWN IN DRAWING, EITHER DIRECT OR IMPLIED,
<br />ARE HEREBY CLARIFIED AS EXAMPLES AND SHALL NOT BE CONSIDERED
<br />COMPLETE DESIGNS FOR CONSTRUCTION. THESE DRAWINGS ARE INTENDED TO
<br />SUPPLEMENT THE SUBMITTAL PACKAGE FROM ARCHITECT.
<br />2. ANY PARTIAL INFORMATION, OMISSIONS, OR INACCURATE DESCRIPTIONS OF
<br />WORK SHOWN IN DRAWINGS, WHICH ARE NECESSARY TO PERFORM THE SCOPE
<br />OF WORK, SHALL NOT RELIEVE THE CONTRACTOR FROM COMPLETION OF
<br />WORK. ALL WORK SHALL BE PERFORMED TO SATISFY THE MINIMUM
<br />REQUIREMENTS OF THE CURRENT APPLICABLE BUILDING CODES.
<br />3. CONTRACTOR SHALL FIELD VERIFY ALL DIMENSIONS AND CONDITIONS PRIOR TO
<br />START OF CONSTRUCTION. THE ARCHITECT SHALL BE PROMPTLY NOTIFIED OF
<br />ANY INCONSISTENCIES AND/OR DISCREPANCIES.
<br />ICONSULTANT
<br />AMERICAN TRASH MANAGEMENT
<br />AMERICAN PM415.292.5400 RFOR IAI946080
<br />92.5410
<br />TRASH MANAGEMENT S'BROW @TRASHMANAGE.COM
<br />ASTM A307%6-18UNCx1 CAP SCREW
<br />W/ STANDARD WASHER & NEOPRENE -
<br />GROMMET, (1) TOTAL PER ASSEMBLY
<br />A36 FLOOR FRAME
<br />SEE PLAN
<br />PROVIDE MASON BRA -RED SOUND
<br />ISOLATION PADS BELOW FRAME
<br />FRAMING BY
<br />OTHERS (S.S.D.)
<br />SIMPSON SPAX#6Wg" PANHEAD ZINC
<br />SCREW, (4) TOTAL PER ASSEMBLY
<br />TYPE III & V FLOOR
<br />CONNECTION
<br />CENTRAL POINTE
<br />SANTA ANA, CA # 2019-0129
<br />PLYWOOD SUBFLOOR
<br />BY OTHERS
<br />SCALE: %2" = V-0"
<br />2HR FIRE -RATED WAI
<br />PER SCHEDULE (S.A.D
<br />A36 FLOOR SUPPO
<br />FRAME, SEE PL
<br />SCALE: 02" = V-0" \
<br />SCHEMATIC DESIGN
<br />JULY 20TH, 2020
<br />NOTES:
<br />1. ATTACHMENT OF ALL BLOCKING, CURBS, AND OTHER ROOF COMPONENTS SHALL BE
<br />DESIGNED AND INSTALLED TO MEET THE MINIMUM REQUIREMENTS OF MANUFACTURER.
<br />2. SEE ARCHITECTURAL AND/OR STRUCTURAL DRAWINGS FOR ALL WORK BY OTHERS.
<br />VENT CAP W/ CURB FLASHING
<br />3 CHUTE VENT
<br />AT ROOF LEVEL
<br />WOOD FRAME & ROOF
<br />ASSEMBLY BY OTHERS (S.S.D.)
<br />2 ^ 1
<br />4 3 2
<br />1
<br />I I
<br />JII 5 III
<br />__--�----- l_-- D&SUNIT (NTS) --_1
<br />- - - - INSTALLED BEHIND F.O. WALL
<br />-- - - - - - - - - - - - -j B
<br />I I
<br />I g I
<br />I I
<br />I
<br />15x15 ACCESS DOOR(NTS) INSTALLED BY
<br />HUTE INTAKE DOOR: 14" MAX OPENING FROM CONTRACTOR PRIOR TO ERECTING WALL
<br />O. WALL, SEE DETAIL 2/- & NOTES 4 & 5 FOR
<br />EIGHT REQUIREMENTS
<br />RE -RATED WALL
<br />;HEDULE (S.A.D.)
<br />34" SQ. OPENING
<br />2HR FIRE -RATED WALL BY
<br />OTHERS, TYP (S.A.D.) SHOWN
<br />FOR CONTEXT ONLY
<br />*WHEN CALCULATING
<br />NUMBER OF FIRE
<br />SPRINKLER HEADS FOR
<br />EVERY OTHER FLOOR
<br />ALWAYS START WITH
<br />HIGHEST LEVEL
<br />FIRE SPRINKLER
<br />HEAD AT
<br />HIGHEST LEVEL
<br />OF BUILDING
<br />*FIRE SPRINKLER
<br />HEAD AT EVERY
<br />OTHER FLOOR
<br />SCALE: 3/e" = 1'-0"
<br />NOTES:
<br />1. 2019 CBC - 11B-404.3.5 HEIGHT: CONTROLS AND OPERATING MECHANISMS SHALL BE LOCATED NO HIGHER
<br />THAN 48 INCHES, AND NO LOWER THAN 15 INCHES ABOVE THE FINISHED FLOOR MEASURED TO THE
<br />CENTER OF THE GRIP.
<br />2. 2019 CBC - 11B-309.4 OPERATION: CONTROLS AND OPERATING MECHANISMS SHALL BE OPERABLE WITH
<br />ONE HAND AND SHALL NOT REQUIRE TIGHT GRASPING, PINCHING, OR TWISTING OF THE WRIST. THE FORCE
<br />REQUIRED TO ACTIVATE CONTROLS AND OPERATING MECHANISMS SHALL BE NO GREATER THAN 5
<br />POUNDS.
<br />23" FROM
<br />F.O. WALL
<br />2HR FIRE -RATED WALL
<br />_T
<br />PER SCHEDULE (S.A.D.)
<br />5 TAPE INTERIOR OF CHUTE SHAFT
<br />TO PREVENT ODOROUS AIR LEAKS
<br />COAT CHUTE W/SOUNDCOAT
<br />4 GP-1 OR KINETICS KDC-E-162
<br />MATCH THICKNESS OF METAL
<br />A36 FLOOR SUPPORT
<br />3 FRAME, SEE PLAN
<br />LEVEL 2
<br />FIRE SPRINKLER
<br />HEAD AT LOWEST
<br />LEVEL OF
<br />BUILDING LEVEL 1
<br />EXAMPLE
<br />BUILDING VERTICAL
<br />SECTION VIEW
<br />II I'
<br />II II
<br />HAN
<br />7 CHUTEASHAFTAT INTAKE
<br />SCALE: 3/8" = 1'-0"
<br />3/4" CONDUIT FOR AIR
<br />1 ' -1 1 3/4 ; /-COMPRESSOR
<br />1" EMT TO POWER
<br />ICD RECYCLING
<br />6y4" 4" DOORS.
<br />3/4" EMT TO WASHDOWN
<br />SOLENOID ABOVE HIGHEST �y
<br />INTAKE. L
<br />2'- 6
<br />MASON BRA -RED MOUNT
<br />TYP. (4)REQUIRED INSIDE FRAME
<br />3'-0" MIN. SHAFT
<br />WOOD FRAME CONSTRUCTION FOR 30" CHUTE
<br />15x18 BOTTOM HINGED
<br />ICD-2000 PNEUMATIC
<br />ASSIST INTAKE DOOR,
<br />14" MAX OPENING
<br />BB
<br />A36 L1y2"x1y2"e, x 41"
<br />FLOOR SUPPORT FRAME
<br />AT 30"0 CHUTE TYP
<br />WATER LINE FOR WASHDOWN
<br />RISER IF NOT PROVIDED
<br />ABOVE HIGHEST INTAKE
<br />(SIZING BY OTHERS)
<br />SPRINKLER RISER
<br />(SIZING BY OTHERS)
<br />FINISH WALL LINE
<br />2HR FIRE -RATE[
<br />PER SCHEDULE (:
<br />TAPE INTERIOR OF I
<br />SHAFT TO PRI
<br />ODOROUS AIR
<br />COAT CHUTE W/ SOUNI
<br />GP-1 OR KINETICS KDC
<br />MATCH THICKNESS OF
<br />A36 FLOOR SUPPORT FRAME, SEE
<br />c
<br />OPP
<br />HAND
<br />PROVIDE BLKG AS REQ'D FOR
<br />CONTINUOUS FIRE RATING AT
<br />FLOOR ASSEMBLY, S.S.D.
<br />2HR FIRE -RATED WALL
<br />PER SCHEDULE (S.A.D.)
<br />NO CONTACT BTWN GYP BOARD, FRAMING &
<br />CHUTE. SEAL GAP W/ FLEXIBLE ACOUSTIC
<br />RATED FIRE CAULKING AT PENETRATION
<br />�y THROUGH WALL & SHAFT, ALL AROUND
<br />Op
<br />/ CHUTE INTAKE DOOR: 14" MAX OPENING
<br />/ FROM F.O. WALL, SEE DETAIL 2/- & NOTES FOR
<br />HEIGHT REQUIREMENTS
<br />FIRE -RATED ACOUSTIC
<br />FLEXIBLE SEALANT
<br />i
<br />TYP RESIDENTIAL LEVEL
<br />SCALE:
<br />RE -RATED WALL
<br />HEDULE (S.A.D.)
<br />NTACT BTWN GYP
<br />), FRAMING & CHUTE.
<br />'AP W/ FLEXIBLE
<br />3TIC RATED FIRE
<br />:ING AT PENETRATION
<br />1GH WALL & SHAFT,
<br />20UND
<br />CHUTEINTAKE
<br />DOOR: 14" MAX
<br />OPENING FROM
<br />F.O. WALL
<br />SEE DETAIL 1/-
<br />ATED ACOUSTIC
<br />ILE SEALANT
<br />2-HR SHAFT SECTION BB AT CENTER WITH SQUARE OPENING
<br />TIMBER CONSTRUCTION
<br />11 SCALE: 9" _ -0"
<br />CHUTE DETAILS
<br />T-200
<br />
|