Laserfiche WebLink
SHEATHING MAY OCCUR3-COAT STUCCO SYSTEMO/ METAL LATH O/ WRBSTUD WALLINTERIOR FINISHSLSTUD WALLINTERIOR FINISH3-COAT STUCCO SYSTEM O/METAL LATH O/ WRB3-COAT STUCCO SYSTEM O/METAL LATH O/ WRBSTUD WALLINTERIOR FINISHAPPLIED FOAM TRIMSEE EXT. ELEVATIONSAPPLIED FOAM TRIMSEE EXT. ELEVATIONSAPPLIED FOAM TRIMSEE EXT. ELEVATIONS1 : 2BOND BREAKER AT STUCCO TO DRIPFLASHING7-7-WRBWEATHER RESISTIVE BARRIERMINIMUM 2-LAYERS FORTIFIBER 60 MINUTE SUPER JUMBO TEXSELF ADHERED FLASHINGFORTIFIBER FORTIFLASH BUTYL 30 MIL AT SILL,20 MIL AT HEAD AND JAMBS U.N.O.SAFBACKER ROD& SEALANTGENERAL NOTES1.VERIFY WINDOW INSTALLATION WITH WINDOW MANUFACTURER'S WRITTEN INSTRUCTIONS.PROVIDE FIELD MOCKUP OF WINDOW INSTALLATION FOR APPROVAL BY OWNER.2.UNLESS SUPERSEDED BY WINDOW MANUFACTURER, THE ROUGH OPENING SHOULD BE 1/2"GREATER IN WIDTH AND HEIGHT THAN THE NET FRAME SIZE OF THE WINDOW.3.VERIFY ROUGH OPENING IS SQUARE, PLUMB, AND LEVEL. WINDOW SILL TO BE SET UPON LEVELFRAMING SILL WITH CONTINUOUS SUPPORT.4.SUBSTRATES SHALL BE CLEAN , DRY, PRIMED AS REQUIRED, AND UNIFORM/SMOOTH PRIOR TOFLASHING APPLICATION.5.WANED LUMBER WILL NOT BE USED @ ROUGH OPENINGS LOCATIONS.6.FIELD VERIFY ALL DIMENSIONS PRIOR TO CUTTING AND INSTALLING FLASHING COMPONENTS.VERIFY MANUFACTURER REQUIREMENTS.7.PROVIDE MINIMUM 12" SOLID WOOD BACKING OR SHEATHING AT ALL SIDES OF OPENING TOSECURE FLASHING.8.ADHERE SELF ADHERED FLASHING TO CLEAN DUST FREE BACKING TYPICAL.9.USE CHEMICALLY COMPATIBLE PRIMERS, WRB, AND SEALANT AS REQUIRED BY MANUFACTURER.10.GSM TO BE MIN. 26 GA G90 GALVANIZED U.N.O.11.PROVIDE GSM SILL PAN AT STOREFRONT TO FLOOR CONDITION - SEE DOOR SILL PAN DETAILSFOR SIM. INFORMATIONLEGEND AND NOTES (APPLIES TO ENTIRE SHEET)WRB O/ SAF O/ GSM HEAD FLASHINGO/ SAF O/ CASING BEAD O/ SAFALUM. STOREFRONT SYSTEM -SEE WINDOW FLASHING DETAILEXTERIOR FACE BACKER ROD &SEALANTWEATHER RESISTIVE BARRIEREXTERIOR FACE BACKER ROD &SEALANTALUM. STOREFRONT SYSTEM -SEE WINDOW FLASHING DETAIL7-ALUM. STOREFRONT SYSTEM -SEE WINDOW FLASHING DETAILEXTERIOR FACE BACKER ROD &SEALANTNOFNAIL ON FLASHINGFORTIFIBER MOISTOP NEXTWRB BIBB O/ J-METAL CASING BEADO/ SAF O/ NOF O/ WRB (3 1/2" LEG)WRB O/ SAF O/ J-METAL CASINGBEAD O/ SAFSL1 : 2BACK DAM - TLS VINYL CORNERSET IN CONT. BEAD OF SEALANTW/ END JOINTS SEALEDBIBB12" WIDE NOF BIBB -EXTEND 12" BEYOND R.O.EA. SIDE"A" PIECEINSTALL TLS LABS 'A' PIECEAT CORNERS PER MANUF.GUIDELINES - SIZE 'A' PIECETO MATCH R.O. DEPTHSILL SAF MEMBRANE30 MIL SILL SAF -COMPLETELY COVER R.O.SILL; RUN PAST R.O. 6" MIN.EA. SIDE TO COVER 'A'PIECES; RUN 4" MIN.DOWNLEG"A" PIECEINSTALL TLS LABS 'A' PIECEAT CORNERS - SIZE 'A'PIECE TO MATCH R.O.DEPTHHEAD SAFHEAD SAF - COMPLETELYCOVER R.O. HEAD - EXTEND1" PAST JAMB SAF EA. SIDE;RUN 4" MIN. UPLEGJAMB SAFJAMB SAF - COMPLETELYCOVER R.O. JAMB - EXTENDTO 1" ABOVE BOTTOM OFNOF SILL BIBB AND 11"BEYOND R.O. HEAD - RUN 4"MIN. SIDELEGSTOREFRONTINSTALL STOREFRONTSYSTEM AND INNER BACKERROD & SEALANT PER MANUF.RECOMMENDATIONS -MAINTAIN MIN. 3/8" SEALANTJOINTCASING BEADINSTALL J- METAL CASINGBEAD (3-1/2" LEG) AT HEAD,JAMBS, AND SILL - MAINTAINMIN. 3/8" SEALANT JOINTBETWEEN CASING BEAD ANDSTORFRONTJAMB SAFINSTALL 9" WIDE JAMB SAF O/CASING BEAD LEG - ALIGN ATTOP AND BOTTOM WITHBASE JAMB SAFHEAD SAFINSTALL HEAD SAF O/CASING BEAD - EXTEND 1"PAST JAMB SAF EA. SIDEINSTALL EXTERIOR FACECONTINUOUS BACKER ROD& SEALANT AT SEALANTGAPSEALANTINSTALL 4" TALL GSM DRIPFLASHING O/ HEAD CASINGBEAD (OR O/ TOP OFHARDIE TRIM AT SIDINGCONDITION) - RUN FLANGE6" PAST DRIP ON EACHSIDE; PROVIDE CLOSEDENDS AT DRIP AND SOLDERALL SEAMSGSM DRIP FLASHINGINSTALL 12" WIDE SAF O/GSM HEAD DRIP FLANGE -RUN 1" PAST EDGE OFJAMB SAF ON EACH SIDEHEAD DRIP SAFINSTALL WRBAT INNER SEAL - MOISTOP SEALANT;AT EXTERIOR FACE - GE SILPRUF 2000 OR DOW CORNING 795WITH COMPATIBLE OPEN CELL BACKER ROD - 3/8" MIN.SEALANT JOINT WIDTHINNER SEAL BACKER ROD & SEALANTINNER SEAL BACKER ROD & SEALANTINNER SEAL BACKER ROD & SEALANTSTOREFRONT DETAILS(FLUSH CONDITIONS)AD-81NOT USED5SF WINDOW HEAD (STUCCO)1SF WINDOW JAMB (STUCCO)2NOT USED68NOTES3SF WINDOW SILL (STUCCO)NOT USED7CCOPYRIGHTIt is the clients responsibility prior to or during construction to notify the architect in writingof any perceived errors or omissions in the plans and specifications of which a contractorthoroughly knowledgeable with the building codes and methods of construction shouldreasonably be aware. Written instructions addressing such perceived errors or omissionsshall be received from the architect prior to the client or clients subcontractors proceedingwith the work. The client will be responsible for any defects in construction if theseprocedures are not followed.Architecture + Planning17911 Von Karman Ave.Suite 200Irvine, CA 92614ktgy.com949.851.2133License StampProject Contact:Email:Principal: Project Designer:Project Director:KTGY Project No:2017-0934Debbie Hollanddholland@ktgy.comWil WongD. SchoolmeesterDebbie HollandDeveloperPHONE NO.4199 CAMPUS DRIVEIRVINE, CA 92612(714) 342-2502415 & 515 E. 4TH STREET, SANTA ANA, CA 92701 <br />4TH AND MORTIMERNo.Date Description06-21-2023 FIFTH BUILDING DEPARTMENT SUBMITTALA03-21-23ADDENDUM A4STOREFRONT FLASHING - FLUSH CONDITION06-21-23