|
TYPICAL DOOR ELEMENTS
<br />DOOR
<br />SCHEDULE
<br />FOR
<br />DETAILS-
<br />SEE
<br />"DOOR
<br />STYLES" & "TYPICAL DOOR DETAILS"
<br />DOOR NOTES
<br />TYPICAL LOCATION OF DOOR AND GATE ELEMENTS IF THEY OCCUR
<br />DOOR
<br />FRAME
<br />A. PUBLIC USE & COMMON USE AREA DOORS AND GATES
<br />SEE DOOR STYLES FOR SPECIFIC DOOR ELEVATION
<br />BOTTOM OF CLOS R
<br />o /
<br />HIGH VIEWPORT **
<br />/d
<br />PUSH BUTTON *
<br />- - - - -
<br />° o - - - - - - -LOW - ** W X 2
<br />DEADBOLT X 0� Q
<br />\ HARDWARE o X VIEWPORT X Q uJ 2 �
<br />Lu Q
<br />o� Q Lu o
<br />z DOORSMOO_ ooLU 00 d
<br />BOTTOM i i Co M L l -
<br />- FIN FLR a 3 & 4 4 & 6
<br />A-510 A-520
<br />oz
<br />UJ
<br />d
<br />Of
<br />o
<br />XX
<br />ig�
<br />2
<br />m
<br />w z
<br />¢ � Q
<br />REMARKS
<br />CBC CHAP 10, 11A DIV III AND 11 B DIV IV
<br />GATES SHALL COMPLY WITH THESE NOTES AS REQUIRED FOR DOORS.
<br />OPENING CLEARANCE
<br />1. ALL ENTRANCE AND EXIT DOORS SHALL HAVE A MINIMUM CLEAR OPENING OF 32 INCHES WITH THE
<br />DOOR OPEN 90 DEGREES FROM ITS CLOSED POSITION, MEASURED BETWEEN THE FACE OF THE DOOR
<br />AND THE OPPOSITE STOP. (1008.1.1, 11B-404.2.3, 1126A.1.1)
<br />4
<br />2. FOR ACCESSIBLE DOOR CLEARANCES REQUIREMENTS, SEE
<br />EFFORT AD-02.0
<br />3. MAXIMUM EFFORT TO OPERATE DOORS SHALL NOT EXCEED 5 POUNDS FOR PUBLIC EXTERIOR
<br />DOORS, 8'h POUNDS FOR COMMON AREA EXTERIOR DOORS, 5 POUNDS FOR INTERIOR DOORS, AND 15
<br />POUNDS FOR FIRE DOORS. (1008.1.3, 1126A.4, 11B-404.2.9)
<br />HARDWARE
<br />4. DOOR CLOSERS SHALL BE ADJUSTED SO THAT FROM AN OPEN POSITION OF 70 DEGREES THE DOOR
<br />WILL TAKE AT LEAST 3 SECONDS TO MOVE TO APPOINT 3 INCHES FROM THE LATCH. (1126A.4.1,
<br />11 B-404.2.8.1)
<br />J
<br />U
<br />w
<br />_
<br />U)Z
<br />Z
<br />v
<br />=
<br />a
<br />w
<br />¢
<br />CO
<br />z
<br />a
<br />w
<br />¢
<br />U)
<br />z
<br />DWELLING
<br />UNIT
<br />DOORS
<br />U1a
<br />A
<br />3' 0"
<br />6' 8"
<br />1 3/4"
<br />SC
<br />SG
<br />WOOD
<br />SG
<br />20
<br />UNIT ENTRY DOOR
<br />U2a
<br />C
<br />3' 0"
<br />8' 0"
<br />1 3/4"
<br />SC
<br />SG
<br />WOOD
<br />SG
<br />PATIO DOOR, TEMPERED GLAZING, DEAD BOLT, MAX. 0.45 U VALUE, MAX. 0.23 SHGC VALUE
<br />U2b
<br />C
<br />3' 0"
<br />8' 0"
<br />1 3/4"
<br />SC
<br />SG
<br />WOOD
<br />SG
<br />PATIO DOOR, TEMPERED GLAZING, INOPERABLE, MAX. 0.45 U VALUE, MAX. 0.23 SHGC VALUE
<br />KICK PLATE MAY OCCUR 16 GA MAX, ANY FOR ADDITIONAL INFORMATION SEE DETAILS
<br />U3a
<br />B
<br />3'-01,
<br />6-8"
<br />1 3/8"
<br />HC
<br />SG
<br />WOOD
<br />SG
<br />BEDROOM, PRIVACY LOCK
<br />THRESHOLDS
<br />LCAVITIES CREATED SHALL BE CAPPED * REQUIRED AT ACCESSIBLE/ADAPTABLE DWELLING UNITS
<br />NO PROJECTIONS INTO ** IF PROVIDED INSTALL TWO VIEWPORTS ONE HIGH ONE
<br />CLEAR OPENING BELOW 34" LOW AT
<br />ACCESSIBLE/ADAPTABLE DWELLING UNITS
<br />5. THRESHOLD - LANDINGS SHALL NOT BE MORE THAN 1/2 INCH LOWER THAN THE TOP OF THE
<br />THRESHOLD OF THE DOORWAY. CHANGES IN HEIGHT BETWEEN %AND Yz INCH SHALL BE BEVELED AT
<br />A MAXIMUM 50%. CHANGES IN LEVEL GREATER THAN''/z INCH SHALL BE RAMPED. (1008.1.7, 1126A.2.1,
<br />11 B-404.2.5)
<br />U4a
<br />B
<br />3' 0"
<br />6-8"
<br />1 3/8"
<br />HC
<br />SG
<br />WOOD
<br />SG
<br />BATHROOM, PRIVACY LOCK
<br />U5a
<br />B
<br />T-0"
<br />6'-8"
<br />1 3/8"
<br />HC
<br />SG
<br />WOOD
<br />SG
<br />CLOSET, PASSAGE HARDWARE
<br />U6a
<br />D
<br />T-0"
<br />6-8"
<br />1 3/8"
<br />HC
<br />SG
<br />WOOD
<br />SG
<br />WASHER/DRYER CLOSET, PASSAGE HARDWARE
<br />B. DWELLING UNIT DOORS
<br />PRIMARY ENTRANCE DOOR INTO AND DOORS WITHIN INDIVIDUAL DWELLING UNITS
<br />6. MAXIMUM EFFORT TO OPERATE DOORS SHALL NOT EXCEED 8'/z POUNDS FOR EXTERIOR DOORS, 5
<br />DOOR STYLES
<br />U6b
<br />D
<br />2'-8"
<br />6'-8"
<br />1 3/8"
<br />HC
<br />SG
<br />WOOD
<br />SG
<br />WASHER/DRYER CLOSET, PASSAGE HARDWARE
<br />POUNDS FOR INTERIOR DOORS, AND 15 POUNDS FOR FIRE DOORS.
<br />7. DOORS FROM INDIVIDUAL DWELLING OR SLEEPING UNITS IN GROUP R OCCUPANCIES HAVING AN
<br />U7a
<br />B
<br />3' 0"
<br />68"
<br />1 3/8"
<br />HC
<br />SG
<br />WOOD
<br />SG
<br />COAT CLOSET, PASSAGE HARDWARE
<br />OCCUPANT LOAD OF 10 OR LESS ARE PERMITTED TO HAVE A NIGHT LATCH, DEAD BOLT OR SECURITY
<br />CHAIN PROVIDED SUCH DEVICES ARE OPENABLE FROM THE INSIDE WITHOUT THE USE OF A KEY OR
<br />U7b
<br />B
<br />2'-10"
<br />6-8"
<br />1 3/8"
<br />HC
<br />SG
<br />WOOD
<br />SG
<br />COAT CLOSET, PASSAGE HARDWARE
<br />TOOL (1008.1.9.3.4) AND ARE OPERABLE WITH A SINGLE EFFORT OF THE DOOR LEVER. (1132A.8)
<br />8. DOOR BUZZER, BELL, CHIME OR EQUIVALENT SHALL BE PROVIDED AT EVERY PRIMARY ENTRANCE
<br />U7c
<br />B
<br />2'-8"
<br />6-8"
<br />1 3/8"
<br />HC
<br />SG
<br />WOOD
<br />SG
<br />COAT CLOSET, PASSAGE HARDWARE
<br />DOOR. (1132A.10)
<br />9. THRESHOLD - SECONDARY EXTERIOR DOORS OF DWELLING UNITS SHALL BE NO HIGHER THAN INCH
<br />U8a
<br />E
<br />10'-4"
<br />6'-8"
<br />1 3/8"
<br />HC
<br />SG
<br />WOOD
<br />SG
<br />BY-PASS, 4 PANELS
<br />U8b
<br />E
<br />8' 0"
<br />6' 8"
<br />1 3/8"
<br />HC
<br />SG
<br />WOOD
<br />SG
<br />BY-PASS
<br />'
<br />FOR SLIDING DOORS OR FOR OTHER DOORS. CHANGES IN HEIGHT BETWEEN 1/4AND 3/4 INCH SHALL
<br />BE BEVELED AT A MAXIMUM 50%. (1008.1.7, 1132A.4.1)
<br />U8c
<br />E
<br />T-0"
<br />6-8"
<br />1 3/8"
<br />HC
<br />SG
<br />WOOD
<br />SG
<br />BY-PASS
<br />TEMP
<br />o
<br />o 0 GL o 0
<br />o o
<br />10. ENTRANCE DOORS FROM INTERIOR CORRIDORS TOGETHER WITH THEIR PERIMETER SEALS SHALL
<br />HAVE A LABORATORY STC RATING OF NOT LESS THAN 26. SUCH TESTED DOORS SHALL OPERATE
<br />NORMALLY WITH COMMERCIALLY AVAILABLE SEALS UNLESS OTHERWISE REQUIRED BY AN
<br />ACOUSTICAL REPORT. (1207.7)
<br />U8d
<br />E
<br />6' 0"
<br />68"
<br />1 3/8"
<br />HC
<br />SG
<br />WOOD
<br />SG
<br />BY-PASS
<br />U8e
<br />E
<br />5'-0"
<br />6'-8"
<br />1 3/8"
<br />HC
<br />SG
<br />WOOD
<br />SG
<br />BY-PASS
<br />11. DOORS ON AN ACCESSIBLE ROUTE SHALL BE OPERABLE WITH A SINGLE EFFORT BY LEVER TYPE
<br />U8f
<br />E
<br />4'-0"
<br />6'-8"
<br />1 3/8"
<br />HC
<br />SG
<br />WOOD
<br />SG
<br />BY-PASS
<br />HARDWARE, PANIC BARS, PUSH-PULL ACTIVATING BARS OR OTHER HARDWARE DESIGNED TO PROVIDE
<br />PASSAGE WITHOUT REQUIRING THE ABILITY TO GRASP, TIGHT PINCHING OR TWISTING OF THE WRIST
<br />TO OPERATE THE OPENING HARDWARE
<br />A B C D E
<br />12. LEVER -TYPE HARDWARE SHALL BE CURVED WITH A RETURN TO WITHIN'/2 INCH OF THE DOOR EXCEPT
<br />IN GROUP R AND U OCCUPANCIES WITH AN OCCUPANT LOAD OF 10 OR LESS.
<br />ENTRY DOOR INTERIOR DOOR FRENCH DOOR LOUVERED DOOR BY-PASS DOOR
<br />13. HARDWARE SHALL BE INSTALLED BETWEEN 34 MINIMUM TO 44 INCHES MAXIMUM ABOVE FINISHED
<br />FLOOR.
<br />14. EGRESS DOORS IN PAIRS, APPROVED AUTOMATIC FLUSH BOLTS SHALL BE PERMITTED PROVIDED
<br />THAT THE DOOR LEAF HAVING THE AUTOMATIC FLUSH BOLTS HAS NO DOORKNOB OR SURFACE
<br />MOUNTED HARDWARE.
<br />15. EGRESS DOORS - MANUALLY OPERATED FLUSH BOLTS OR SURFACE BOLTS ARE NOT PERMITTED.
<br />16. FIRE DOORS AND BOTH LEAVES OF PAIRS OF SIDE HINGED SWINGING FIRE DOORS SHALL BE
<br />PROVIDED WITH AN ACTIVE LATCH BOLT THAT WILL SECURE THE DOOR WHEN IT IS CLOSED.
<br />17. FIRE DOORS SHALL BE SELF -CLOSING OR AUTOMATIC CLOSING. AUTOMATIC -CLOSING FIRE DOORS
<br />ASSEMBLIES SHALL BE SELF -CLOSING IN ACCORDANCE WITH NFPA 80
<br />18. SMOKE ACTIVATED DOORS - AUTOMATIC CLOSING DOORS SHALL CLOSE BY THE ACTUATION OF SMOKE
<br />DETECTORS IN ACCORDANCE WITH SECTION 907.3 OR BY LOSS OF POWER.
<br />19. INSTALL DOOR HARDWARE IN COMPLIANCE WITH MANUFACTURER'S INSTALLATION REQUIREMENTS.
<br />20. PROTECT ALL THRESHOLDS COMPONENTS FROM DIRECT CONTACT WITH DISSIMILAR METALS AND
<br />CORROSIVE MATERIALS PER MANUFACTURER'S RECOMMENDATIONS.
<br />21. DOORS ON AN ACCESSIBLE ROUTE: THE BOTTOM 10 INCHES MINIMUM OF ALL DOORS AND OR GATES
<br />SHALL HAVE A SMOOTH UNINTERRUPTED SURFACE TO ALLOW THE DOOR OR GATE TO BE OPENED BY
<br />A WHEELCHAIR FOOTREST WITHOUT CREATING A TRAP OR HAZARDOUS CONDITION.
<br />22. GLAZING IN DOORS SHALL COMPLY WITH SAFETY GLAZING (2406) RATINGS
<br />23. FIRE DOOR ASSEMBLIES THAT ARE SIDE HINGED OR PIVOTED SWINGING SHALL BE TESTED IN
<br />ACCORDANCE WITH NFPA 252 OR UL 10C.
<br />24. FIRE DOOR ASSEMBLIES WITH OTHER TYPES OF DOORS INCLUDING SWINGING ELEVATOR DOORS AND
<br />FIRE SHUTTER ASSEMBLIES SHALL BE TESTED IN ACCORDANCE WITH NFPA 252 OR UL10B
<br />25. FIRE DOOR ASSEMBLIES REQUIRED TO HAVE A MINIMUM FIRE PROTECTION RATING OF 20 MINUTES
<br />WHERE LOCATED IN A CORRIDOR OR SMOKE BARRIER WALLS HAVING A FIRE RESISTANCE RATING IN
<br />ACCORDANCE WITH TABLE 715.4 SHALL BE TESTED IN ACCORDANCE WITH NFPA 252 OR UL 10C
<br />WITHOUT THE HOSE STREAM TEST.
<br />26. SMOKE AND DRAFT CONTROL - FIRE DOOR ASSEMBLIES REQUIRED TO HAVE A MINIMUM FIRE
<br />PROTECTION RATING OF 20 MINUTES WHERE LOCATED IN A CORRIDOR OR SMOKE BARRIER WALLS
<br />SHALL MEET THE REQUIREMENTS FOR SMOKE AND DRAFT CONTROL DOOR ASSEMBLIES TESTED IN
<br />ACCORDANCE WITH UL 1784
<br />27. GLAZING IN DOOR ASSEMBLY - IN 20 MINUTE FIRE DOOR ASSEMBLY, THE GLAZING MATERIAL IN THE
<br />DOOR ITSELF SHALL HAVE A MINIMUM FIRE -PROTECTION -RATED -GLAZING OF 20 MINUTES.
<br />28. FIRE DOOR ASSEMBLIES IN EXIT ENCLOSURES AND EXIT PASSAGE WAYS SHALL HAVE A MAXIMUM
<br />TRANSMITTED TEMPERATURE END POINT OF NOT MORE THAN 450 F DEGREES. THIS IS NOT REQUIRED
<br />WHEN BUILDING IS EQUIPPED THROUGHOUT WITH AN NFPA 13 AUTOMATIC SPRINKLER SYSTEM.
<br />29. DOOR FRAMES WITH TRANSOM LIGHTS, SIDELIGHTS OR BOTH, SHALL BE PERMITTED WHERE A'/4 HOUR
<br />FIRE PROTECTION RATING OR LESS IS REQUIRED. WHERE A FIRE PROTECTION RATING EXCEEDING %
<br />HOUR IS REQUIRED FIRE DOOR FRAMES WITH TRANSOM LIGHTS, SIDELIGHTS OR BOTH SHALL BE
<br />INSTALLED WITH FIRE -RESISTANCE -RATED GLAZING TESTED AS AN ASSEMBLY IN ACCORDANCE WITH
<br />ASTM El19 OR UL 263.
<br />30. DOORS THAT ARE PART OF A FIRE RATED WALL ASSEMBLY SHALL COMPLY WITH OPENING
<br />PROTECTIVES.
<br />LABELS
<br />31. FIRE DOOR ASSEMBLIES SHALL BE LABELED BY AN APPROVED AGENCY. THE LABELS SHALL COMPLY
<br />WITH NFPA 80 AND SHALL BE PERMANENTLY AFFIXED TO THE DOOR OR FRAME.
<br />32. FIRE DOORS SHALL BE LABELED SHOWING THE NAME OF THE MANUFACTURER, THE NAME OR
<br />TRADEMARK OF THE THIRD -PARTY INSPECTION AGENCY, THE FIRE PROTECTION RATING AND WHERE
<br />REQUIRED FOR FIRE DOORS IN EXIT ENCLOSURES AND EXIT PASSAGEWAYS THE MAXIMUM
<br />TRANSMITTED TEMPERATURE END POINT. LABELS SHALL BE APPROVED AND PERMANENTLY AFFIXED
<br />AND FACTORY APPLIED. SMOKE AND DRAFT CONTROL DOORS COMPLYING WITH UL 1784 SHALL SHOW
<br />THE LETTER "S" ON THE FIRE RATED LABEL.
<br />33. OVERSIZED FIRE DOORS SHALL BEAR AN OVERSIZED FIRE DOOR LABEL BY AN APPROVED AGENCY OR
<br />SHALL BE PROVIDED WITH A CERTIFICATE OF INSPECTION BY AN APPROVED TESTING AGENCY.
<br />34. FIRE DOOR FRAMES SHALL BE LABELED SHOWING THE NAME OF THE MANUFACTURER AND THE
<br />THIRD -PARTY INSPECTION AGENCY.
<br />35. GLAZING - FIRE -PROTECTION- RATED GLAZING SHALL BEAR A LABEL OR OTHER IDENTIFICATION
<br />SHOWING THE NAME OF THE MANUFACTURER, THE TEST STANDARD AND THE FOLLOWING FOUR PART
<br />IDENTIFICATION ISSUED BY AN APPROVED AGENCY AND PERMANENTLY AFFIXED TO THE GLAZING.
<br />THE LABEL SHALL BEAR THE FOLLOWING FOUR PART IDENTIFICATION:
<br />"D-HORNH -TORNT-XXX"
<br />D INDICATES THE GLAZING SHALL BE USED IN FIRE DOORS PER NFPA 252
<br />H OR NH INDICATES THE GLAZING MEETS OR DOES NOT MEET THE HOSE STREAM TEST
<br />T OR NT INDICATES THE GLAZING MEETS OR DOES NOT MEET THE TEMPERATURE REQUIREMENTS
<br />XXX INDICATES THE FIRE -PROTECTION -RATING PERIOD IN MINUTES.
<br />36. EXTERIOR DOORS SHALL BE INSTALLED BEARING MANUFACTURER'S CERTIFICATE OF COMPLIANCE
<br />WITH SPECIFIED THERMAL AND ACOUSTICAL REQUIREMENTS.
<br />WEATHERIZATION
<br />37. DOORS SHALL HAVE ALL SIX SIDES FACTORY PRIMED OR SEALED AFTER HARDWARE PREPARATION.
<br />RESEAL ALL SURFACES IMMEDIATELY AFTER INSTALLATION.
<br />38. EXTERIOR DOORS SHALL BE INSULATED AND FULLY WEATHER STRIPPED.
<br />39. REFER TO REFERENCED DETAILS OF EXTERIOR DOORS FOR INTEGRATION WITH EXTERIOR WALL AND
<br />THRESHOLD FLASHING SYSTEMS.
<br />40. INSULATE SHIM CAVITY AROUND EXTERIOR DOORS WITH LOW EXPANSION FOAM.
<br />41. FOR DOOR/ FRAME ASSEMBLIES IN C.M.U. VERIFY MASONRY OPENING DIMENSIONS.
<br />42. PROVIDE SEPARATION BY A TIGHT FITTING DOOR BETWEEN FOOD PREPARATION AREA(S) (INCLUDING
<br />FOOD STORAGE ROOMS) AND TOILET ROOM(S). SECTION 302.6
<br />GLAZING PERFORMANCE
<br />GLAZING LOCATION
<br />U VALUE
<br />SHGC
<br />EXTERIOR DOORS
<br />.45
<br />.23
<br />BLDG A STOREFRONT
<br />.46
<br />.22
<br />BLDG B STOREFRONT
<br />.46
<br />.22
<br />DOOR STC RATINGS
<br />LIVING UNIT ENTRY DOORS AND PATIO DOORS SHALL BE SOUND -RATED, PROVIDING A MINIMUM
<br />STC RATING WHEN IN THE CLOSED POSITION. IN ACCORDANCE WITH THE ACOUSTICAL REPORT.
<br />TYPICAL DOOR OPENINGS
<br />DOOR ABBREVIATIONS
<br />2-HR 1-HR
<br />X X X
<br />AL ALUMINUM P PAINT
<br />AD-XX AD-XX AD-XX / \
<br />/
<br />X
<br />/ AD-XX / \
<br />X / \
<br />AD-XX TEMP TEMP
<br />AN ANODIZED PASS PASSAGE
<br />AUTO AUTOMATIC CLOSING PB PUSH BUTTON
<br />ECA ELECTRONIC CONTROL ACCESS PFSF PRE -FINISHED STEEL FRAME
<br />F FACTORY PH PANIC HARDWARE
<br />FGL FIBERGLASS PR PAIR
<br />FF FACTORY FINISH PRIV PRIVACY LOCK
<br />FX FIXED S STAIN
<br />V GL GL /
<br />X L------J L------J
<br />\ AD XX X
<br />FIR FRENCH DOOR SC SOLID CORE
<br />GL GLASS SELF SELF CLOSING
<br />HC HOLLOW CORE SG SEMI -GLOSS PAINT
<br />HM HOLLOW METAL STRF STORE FRONT
<br />AD XX \
<br />MA MASONITE TG TEMPERED GLASS
<br />MC MINERAL CORE TS TUBE STEEL
<br />UNIT FIRE DOOR X STOREFRONT
<br />DOOR AD XX DOOR
<br />MTL METAL WD WOOD
<br />N/R NON -RATED
<br />OCG OVERHEAD COILING GRILLE
<br />OCD OVERHEAD COILING DOOR
<br />Architecture + Planning
<br />17911 Von Karman Ave.
<br />Suite 200
<br />Irvine, CA 92614
<br />ktgy.com
<br />949.851.2133
<br />KTGY Project No: 2017-0934
<br />Project Contact: Debbie Holland
<br />Email: dholland@ktgy.com
<br />Principal: Wil Wong
<br />Project Designer: D. Schoolmeester
<br />Project Director: Debbie Holland
<br />Developer
<br />EI7 OAK
<br />INVES'1'1%,iEN'1'S
<br />4199 CAMPUS DRIVE
<br />IRVINE, CA 92612
<br />PHONE NO. (714) 342-2502
<br />1
<br />TF
<br />V_
<br />O
<br />N
<br />Q
<br />U
<br />Q
<br />z
<br />Q
<br />Q
<br />z
<br />Q
<br />U)
<br />LU
<br />U)
<br />F_
<br />NT
<br />w
<br />Ln
<br />Ln
<br />06
<br />T_
<br />Nt
<br />No. Date Description
<br />It is the clients responsibility prior to or during construction to notify the architect in writing
<br />of any perceived errors or omissions in the plans and specifications of which a contractor
<br />thoroughly knowledgeable with the building codes and methods of construction should
<br />reasonably be aware. Written instructions addressing such perceived errors or omissions
<br />shall be received from the architect prior to the client or clients subcontractors proceeding
<br />with the work. The client will be responsible for any defects in construction if these
<br />procedures are not followed.
<br />SED ARC,yjT
<br />�G R
<br />No. C29795
<br />RENEWAL DATE
<br />AUGUST 31, 2023
<br />s�gTF
<br />�F CAS\
<br />License Stamp
<br />DWELLING UNIT DOOR
<br />SCHEDULE
<br />A7-00
<br />z
<br />Q
<br />J
<br />U)
<br />Ir-n
<br />0.
<br />ILL
<br />0
<br />N
<br />1
<br />Ir-
<br />C)
<br />00
<br />C)
<br />COPYRIGHT (C
<br />
|