|
SPACE ALLOWANCES AND REACH RANGES SHALL COMPLY WITH CBC SECTIONS 1138A,11 B-DIVISION 3 & 11 B-DIVISION 4.
<br />CONTROLS AND OPERATING MECHANISMS SHALL COMPLY WITH CBC SECTIONS 1138A.4,1142A AND 116-309.
<br />RAB BARS, TUB AND SHOWER SEATS SHALL COMPLY WITH CBC SECTIONS 1127A.4.
<br />SINGLE -ACCOMMODATION TOILET FACILITIES SHALL COMPLY WITH CBC SECTION 1127A.2.2 AND 11 B-603.
<br />LANDINGS AND THRESHOLDS SHALL COMPLY WITH CBC SECTIONS 1010.1.6, 1010.1.7, 1126A.2 AND 11 B-302, 11 B-303 I
<br />THIS SHEET IS FOR REFERENCE ONLY AND ILLUSTRATES CODE -REQUIRED MINIMUM STANDARDS FOR COMMON
<br />AND PUBLIC USE FACILITIES WITHIN A MULTIFAMILY DEVELOPMENT. SEE PERTINENT SHEETS, DRAWINGS, AND
<br />A. WHEELCHAIR PASSAGE AND PASSING WIDTHS THE MINIMUM CLEAR WIDTH FOR WHEELCHAIR PASSAGE IS 361,
<br />A. GENERAL.
<br />A. GRAB BARS SHALL BE INSTALLED IN A HORIZONTAL POSITION, 33" MINIMUM AND 36" MAXIMUM ABOVE THE FINISH
<br />A. THERE SHALL BE SUFFICIENT SPACE IN THE TOILET ROOM FOR A WHEELCHAIR MEASURING 30" WIDE BY 48"
<br />SPECIFICATIONS FOR APPLICATION OF THESE STANDARDS TO THIS SPECIFIC PROJECT.
<br />CONTINUOUSLY. A 32" WIDTH IS ACCEPTABLE AT A POINT NOT TO EXCEED 24" IN LENGTH, SEE FIGURE 1. SEE FIGURE 2.
<br />CONTROLS AND OPERATING MECHANISMS IN ACCESSIBLE SPACES, ALONG ACCESSIBLE ROUTES OR AS PART OF
<br />FLOOR MEASURED TO THE TOP OF THE GRIPPING SURFACE.
<br />LONG TO ENTER THE ROOM AND PERMIT THE DOOR TO CLOSE . THERE SHALL BE IN THE ROOM A CLEAR
<br />FOR THE MINIMUM WIDTH FOR TWO WHEELCHAIRS TO PASS IS 60".
<br />ACCESSIBLE ELEMENTS AND THOSE REQUIRED TO BE ACCESSIBLE BY CBC SECTION 1.9.1 SHALL COMPLY WITH THE
<br />EXCEPTION: THE HEIGHT OF THE LOWER GRAB BAR ON THE BACK WALL OF A BATHTUB SHALL COMPLY WITH
<br />FLOOR SPACE OF AT LEAST 60" IN DIAMETER, OR A T-SHAPED SPACE COMPLYING WITH DETAIL 22, NOTE B, OF
<br />a
<br />THE INFORMATION CONTAINED WITHIN THESE SHEETS ARE EXCERPTS FROM THE CALIFORNIA BUILDING CODE
<br />36"MIN.
<br />FOLLOWING REQUIREMENTS;
<br />SECTION 1127A.5.2.
<br />THIS SHEET; SEE FIGURES 9.1 AND 9.2 BELOW. NO DOOR SHALL NOT ENCROACH INTO THIS CLEAR FLOOR
<br />� Q
<br />(CBC) AND FAIR HOUSING ACT (FHA) DESIGN MANUAL, AND INTENDED TO PROVIDED THE CONTRACTOR THE
<br />4"MIN. CLR.
<br />B. CLEAR FLOOR SPACE.
<br />B. THE DIAMETER OR WIDTH OF THE GRIPPING SURFACES OF A GRAB BAR SHALL COMPLY WITH THE FOLLOWING:
<br />SPACE FOR MORE THAN 12"; SEE FIGURE 9.2 BELOW.
<br />w w
<br />GENERAL REQUIREMENTS OF ACCESSIBILITY FOR THIS PROJECT. THE GENERAL CONTRACTOR SHALL BE
<br />CLEAR 44" MIN. CORRIDOR
<br />A CLEAR FLOOR SPACE THAT ALLOWS A FORWARD OR PARALLEL APPROACH BY A PERSON USING A WHEELCHAIR
<br />1. GRAB BARS WITH CIRCULAR CROSS SECTION SHALL HAVE AN OUTSIDE DIAMETER OF 14'.
<br />B. WHEN A TOILET ROOM OR BATHING ROOM IS FOR INDIVIDUAL USE AND A CLEAR FLOOR SPACE COMPLYING
<br />> M
<br />" o-
<br />KNOWLEDGEABLE OF AND SHALL BUILD TO ALL APPLICABLE ACCESSIBILITY CODE REQUIREMENTS, IF FURTHER
<br />< 10 OC CLEAR WIDTH
<br />SHALL BE PROVIDED AT CONTROLS AND OPERATING MECHANISMS.
<br />2. GRAB BARS WITH NON CIRCULAR CROSS SECTION SHALL HAVE A CROSS SECTION DIMENSION OF 2" MAXIMUM. THE
<br />WITH DETAIL 22, NOTE C, OF THIS SHEET, IS PROVIDED WITHIN THE ROOM BEYOND THE ARC OF THE DOOR
<br />�
<br />INFORMATION OR CLARIFICATION IS REQUIRED, CONSULT THE ARCHITECT OR REFERENCE THE CBC AND FHA
<br />LOAD >_ 10 OCC. o
<br />- X z LOAD � ,r Q
<br />N o > p o
<br />C. HEIGHT.
<br />CONTROLS AND OPERATING MECHANISMS SHALL BE LOCATED NO HIGHER THAN 48", AND NO LOWER THAN 15", ABOVE
<br />FINISHED FLOOR MEASURED TO THE CENTER OF THE GRIP. IF THE REACH IS OVER AN OBSTRUCTION EXAMPLE,
<br />PERIMETER DIMENSION OF GRAB BARS WITH NON -CIRCULAR CROSS SECTION SHALL BE 4" MINIMUM AND AND
<br />4.8" MAXIMUM.
<br />SWING, DOORS SHALL BE PERMITTED TO SWING INTO THE CLEAR FLOOR SPACE OR CLEARANCE REQUIRED
<br />FOR ANY FIXTURE; SEE FIGURE 9.2 BELOW.
<br />C. PROVIDE ONE ACCESSIBLE WATER CLOSET IN COMPLIANCE WITH THE REQUIREMENTS WITHIN THIS DETAIL
<br />DESIGN MANUAL PRIOR TO FABRICATION OR INSTALLATION OF THE WORK.
<br />COMMON USE FACILITIES SHALL COMPLY WITH CBC CHAPTER 11A AND ANSI A117.1 AS REFERENCED BY THE FAIR
<br />+ z
<br />(FOR
<br />3. L-SHAPED OR U-SHAPED GRAB BARS SHALL BE PERMITTED.
<br />o - z �
<br />z w
<br />z o � Q c� v
<br />WASTHER OR DRYER ,CONTROLS AND OPERATING MECHANISMS SHALL BE LOCATED WITHIN THE REACH RANGES
<br />SPECIFIED IN SECTION 1138A.3. SEE DETAIL 22 ON THIS SHEET. CONTROLS AND OPERATING MECHANISMS THAT DO
<br />C. THE STRUCTURAL STRENGTH OF GRAB BARS, TUB AND SHOWER SEATS, FASTENERS AND MOUNTING DEVISES SHALL
<br />AND DETAIL 1 N THI HEET. PR VIDE NE LAVAT RY IN MPLIAN E WITH DETAIL 12 F THI HEET.
<br />0 0 SS 0 0 0 CO C 0 SS
<br />D. ALL DOORS FIXTURES AND CONTROLS SHALL BE ON AN ACCESSIBLE ROUTE. THE MINIMUM CLEAR WIDTH OF
<br />BEVEL /
<br />2
<br />HOUSING ACT FHA DESIGN MANUAL. IF COMMON USE FACILITIES ARE MADE AVAILABLE TO THE PUBLIC IF ONLY
<br />( )
<br />PERIODICALLY, THEY MUST COMPLY WITH CBC CHAPTER 11 B AND ADAS N ADDITION TO THE REQUIREMENTS LISTED
<br />. o - Q p
<br />2" MIN. � w . W M � J
<br />Q
<br />NOT SATISFY THESE SPECIFICATIONS ARE ACCEPTABLE, PROVIDED THAT COMPARABLE MECHANISMS, CONTROLS OR
<br />MEET THE FOLLOWING SPECIFICATIONS:
<br />1. BENDING STRESS IN A GRAB BAR OR SEAT INDUCED BY THE MAXIMUM BENDING MOMENT FROM THE APPLICATION
<br />AN ACCESSIBLE ROUTE SHALL BE 36" EXCEPT AT DOORS. SEE DETAIL 4 OF THIS SHEET.
<br />E. THE ACCESSIBLE ROUTE AND TOILET ROOM FLOOR SHALL BE STABLE, FIRM AND SLIP RESISTANT.
<br />J 2%MAXIMUM SLOPE �/
<br />g , g w 1
<br />U) AT EXTERIOR LANDING
<br />ABOVE DURING PERIODS OF PUBLIC USE.
<br />CLEAR v c> L 60"MIN. CLR. o
<br />L C�
<br />OUTLETS, THAT PERFORM THE SAME FUNCTIONS, ARE PROVIDED WITHIN THE SAME AREA AND ARE ACCESSIBLE.
<br />D. OPERATION.
<br />OF A 250-POUND POINT LOAD SHALL BE LESS THAN THE ALLOWABLE STRESS FOR THE MATERIAL OF THE GRAB BAR
<br />F. GRAB BARS SHALL BE INSTALLED IN COMPLIANCE WITH DETAILS 10 & 13 OF THIS SHEET.
<br />_ =
<br />= m
<br />WHEN PROVIDED, COMMON USE AREAS AND FACILITIES IN COVERED MULTIFAMILY DEVELOPMENTS SHALL BE
<br />PASSING
<br />X z
<br />N Q b (CORRIDOR OVER 2G 60" MIN. CLR.
<br />CONTROLS AND OPERATING MECHANISMS SHALL BE OPERABLE WITH ONE HAND AND SHALL NOT REQUIRE TIGHT
<br />OR SEAT.
<br />2. SHEAR STRESS INDUCED IN A GRAB BAR OR SEAT BY THE APPLICATION OF A 250-POUND POINT LOAD SHALL BE
<br />G. THE ENTRANCE DOOR SHALL BE PROVIDED WITH A PRIVACY LOCK OR LATCH IN COMPLIANCE WITH DETAIL 4
<br />OF THIS SHEET.
<br />ACCESSIBLE TO PERSONS WITH DISABILITIES. COMMON USE FACILITIES INCLUDE, BUT ARE NOT LIMITED TO;
<br />LOBBIES, TOILET AND BATHING FACILITIES, LAUNDRY FACILITIES,COMMUNITY ROOMS, CLUBHOUSES, HEALTH AND
<br />GRASPING, PINCHING OR TWISTING OF THE WRIST. THE FORCE REQUIRED TO ACTIVATE CONTROLS SHALL BE NO
<br />GREATER THAN 5 POUNDS OF FORCE.
<br />LESS THAN THE ALLOWABLE SHEAR STRESS FOR THE MATERIAL OF THE GRAB BAR OR SEAT, AND IF ITS MOUNTING
<br />DOOR LANDINGS
<br />FITNESS FACILITIES, GAME ROOMS AND PORTIONS OF COMMON USE TENANT STORAGE. ALL ENTRANCES, DOORS,
<br />FIGURE 1 WHEELCHAIR PASSAGE FIGURE 2 WHEELCHAIR PASSING
<br />E. INSTALLATION HEIGHTS OF ELECTRICAL SWITCHES AND RECEPTACLE OUTLETS.
<br />BRACKET OR OTHER SUPPORT IS CONSIDERED TO BE FULLY RESTRAINED, THEN DIRECT OR TORSIONAL SHEAR
<br />48" MIN DOORS SHALL 48" MIN
<br />A. THE FLOOR OR LANDING ON EACH SIDE OF AN EXIT DOOR SHALL BE LEVEL.
<br />FIXTURES AND CONTROLS SHALL BE ON AN ACCESSIBLE ROUTE.
<br />1. ELECTRICAL SWITCHES. CONTROLS AND SWITCHES INTENDED FOR USE BY THE OCCUPANT OF THE ROOM OR
<br />STRESSES SHALL NOT EXCEED THE ALLOWABLE SHEAR STRESS.
<br />ANEUVERIN COMPLY WITH THE ANEUVERIN
<br />REQUIREMENTS
<br />PUBLIC USE FACILITIES AND AREAS SHALL COMPLY WITH CBC CHAPTER 11 B AND ADAS. WHEN PROVIDED, PUBLIC
<br />B. WHEELCHAIR TURNING SPACE SHALL COMPLY WITH ONE OF THE FOLLOWING FIGURES:
<br />60" 2" 36" 2"
<br />AREA TO CONTROL LIGHTING AND RECEPTACLE OUTLETS, APPLIANCES OR COOLING, HEATING AND VENTILATING
<br />EQUIPMENT SHALL BE LOCATED NO MORE THAN 48" MEASURED FROM THE TOP OF THE OUTLET BOX NOR LESS
<br />THAN 15" FROM THE BOTTOM OF THE OUTLET BOX TO THE FINISH FLOOR OF THE WORKING PLATFORM.
<br />2. ELECTRICAL RECEPTACLE OUTLETS. ELECTRICAL RECEPTACLE OUTLETS ON BRANCH CIRCUITS OF 30 AMPERES
<br />3. SHEAR FORCE INDUCED IN A FASTENER OR MOUNTING DEVICE FROM THE APPLICATION OF A 250-POUND POINT
<br />LOAD SHALL BE LESS THAN THE ALLOWABLE LATERAL LOAD OF EITHER THE FASTENER OR MOUNTING DEVICE OR
<br />THE SUPPORTING STRUCTURE, WHICHEVER IS THE SMALLER LOAD.
<br />4. TENSILE FORCE INDUCED BY A FASTENER BY A DIRECT TENSION FORCE OF A 250-POUND POINT LOAD PLUS THE
<br />SPACE SPACE
<br />OF DETAIL 4 OF
<br />THIS SHEET
<br />LAV. OR LAV. OR
<br />O ©
<br />DOOR THRESHOLDS
<br />A. THRESHOLDS AND CHANGES IN ELEVATION AT DOORS SHALL NOT BE MORE THAN 1/2" LOWER THAN THE TOP
<br />OF THE THRESHOLD OF THE DOORWAY.
<br />B. THRESHOLDS WITH A CHANGE IN HEIGHT OF NOT MORE THAN 1/4" MAY BE VERTICAL.
<br />USE FACILITIES AND AREAS FACILITIES IN COVERED MULTIFAMILY DEVELOPMENTS SHALL BE ACCESSIBLE TO
<br />PERSONS WITH DISABILITIES.
<br />z
<br />-� -'���` ;-------; =
<br />OR LESS AND COMMUNICATION SYSTEM RECEPTACLES SHALL BE LOCATED NO MORE THAN 481, MEASURED FROM
<br />THE TOP OF THE OUTLET BOX NOR LESS THAN 15" FROM THE BOTTOM OF THE OUTLET BOX TO THE FINISH FLOOR
<br />MAXIMUM MOMENT FROM THE APPLICATION OF A 250 POUND POINT LOAD, SHALL BE LESS THAN THE ALLOWABLE
<br />I'--`
<br />FIXTURE - FIXTURE
<br />� _ _
<br />-:_ _ - -- -
<br />C. CHANGES IN LEVEL BETWEEN 1/4" AND 1/2" SHALL BE BEVELED WITH A SLOPE NO GREATER THAN 1 VERTICAL
<br />UNIT TO 2 UNITS HORIZONTAL. CHANGES GREATER THAN 1/2" SHALL BE ACCOMPLISHED BY MEANS OF A RAMP.
<br />PUBLIC USE FACILITIES INCLUDE, BUT ARE NOT LIMITED TO; RENTAL OFFICES, SALES OFFICES AND MAINTENANCE
<br />FACILITIES. THESE AREAS, BY THEIR NATURE, ARE OPEN TO PEOPLE OTHER THAN RESIDENTS AND THEIR GUESTS.
<br />' , ' ' v
<br />\ , , N
<br />_ ' �_,
<br />' co F
<br />OR THE WORKING PLATFORM. EXCEPTIONS INCLUDE TO FOLLOWING CONDITIONS:
<br />a. RECEPTACLE OUTLETS INSTALLED AS PART OF PERMANENTLY INSTALLED BASEBOARD HEATERS ARE
<br />EXEMPT.
<br />WITHDRAWAL LOAD BETWEEN THE FASTENER AND THE SUPPORTING STRUCTURE.
<br />5. GRAB BARS SHALL NOT ROTATE WITHIN THEIR FITTINGS.
<br />C. A GRAB BAR AND ANY WALL OR OTHER SURFACE ADJACENT TO IT SHALL BE FREE OF ANY SHARP OR ABRASIVE
<br />w 1 I �Q w / 12
<br />p cD c) 4 & o CD U I� ��
<br />o Z Q 1 z W o z 0- 4Q- I z W
<br />0 � � �`� 1 0 � � 1
<br />w / Q w Q
<br />z > 1 I _ J z > 1 ; J
<br />DOOR MATS
<br />A. IF A DOORMAT IS USED IN A COMMON USE AREA OR PUBLIC USE AREA, IT SHALL HAVE A FIRM BACKING OR NO
<br />THEY, THEREFORE, MUST COMPLY.
<br />_
<br />% , , M 36"MIN. 8 IN 36"MIN.
<br />b. REQUIRED RECEPTACLE OUTLETS SHALL BE PERMITTED IN FLOORS WHEN ADJACENT TO SLIDING PANELS OR
<br />ELEMENTS AND SHALL HAVE ROUNDED EDGES.
<br />\P� \P�
<br />� w , 1 \ 0 1 ' ED o w U 1 o �/ � � u
<br />1 1 1 1
<br />BACKING.
<br />'� -- ' L------------J
<br />L 60� L z �
<br />z � �
<br />WALLS.
<br />c. BASEBOARD ELECTRICAL OUTLETS USED IN RELOCATABLE PARTITIONS, WINDOW WALLS OR OTHER
<br />ELECTRICAL CONVENIENCE FLOOR OUTLETS ARE NOT SUBJECT TO THE MINIMUM HEIGHT REQUIREMENTS.
<br />D. ADJACENT ELEMENTS, FOR EXAMPLE WATER CLOSET FLUSH VALVES, SHALL BE POSITIONED TO PROVIDE
<br />UNOBSTRUCTED USE OF THE GRAB BARS AT THE SPECIFIED LOCATIONS. THE SPACE BETWEEN THE GRAB BAR AND
<br />PROJECTING OBJECTS BELOW AND AT THE ENDS SHALL BE 1 112"MINIMUM. THE SPACE BETWEEN THE GRAB BAR AND
<br />_ z � __� _ z y__-�
<br />I � o I 1
<br />g, THE MAXIMUM PILE HEIGHT SHALL BE 112".
<br />C. EXPOSED EDGES OF THE DOORMAT SHALL BE FASTENED TO THE FLOOR SURFACE AND HAVE TRIM ALONG
<br />THE ENTIRE LENGTH OF EXPOSED EDGES THAT SHALL COMPLY WITH THE REQUIREMENTS FOR CHANGES IN
<br />60" DIAMETER FOR T-SHAPE FOR = - ��
<br />'� �
<br />d. IN EXISTING BUILDINGS WHEN THE ENFORCING AGENCY DETERMINES THAT COMPLIANCE WITH THESE
<br />STANDARDS WOULD CREATE AN UNREASONABLE HARDSHIP.
<br />PROJECTING OBJECTS ABOVE SHALL BE 12"MINIMUM.
<br />1. THE SPACE BETWEEN THE GRAB BARS AND SHOWER CONTROLS, SHOWER FITTINGS, AND OTHER GRAB BARS
<br />59"MIN. AT 59"MIN. AT
<br />FLR. MTD. W.C. FLR. MTD. W.C.
<br />LEVEL;
<br />1. CHANGES IN LEVEL SHALL NOT EXCEED 1/2".
<br />180 TURNS 180 TURNS o -
<br />ABOVE SHALL BE PERMITTED TO BE 1 1/2" MINIMUM.
<br />OR 56" MIN. AT OR 56" MIN. AT
<br />2. WHEN CHANGES IN LEVEL DO OCCUR, THEY SHALL BE BEVELED WITH A SLOPE NO GREATER THAN 1
<br />42" MIN. < 8" 42" MIN.
<br />1 1/2" MIN
<br />WALL MTD. W.C. WALL MTD. W.C.
<br />UNIT VERTICAL IN 2 UNITS HORIZONTAL (50% SLOPE).
<br />CLR. FLR. SPACE CLR. FLR. SPACE
<br />3. CHANGES IN LEVEL NOT EXCEEDING 1/4" MAY BE VERTICAL.
<br />C. CLEAR FLOOR OR GROUND SPACE FOR WHEELCHAIRS. SHALL COMPLY WITH THE FOLLOWING:
<br />GRAB BAR 1 1/4" TO
<br />4. CHANGES IN LEVEL GREATER THAN 112" SHALL BE MADE BY MEANS OF A SLOPED SURFACE WITH A
<br />1. SIZE AND APPROACH THE MINIMUM CLEAR FLOOR OR GROUND SPACE REQUIRED TO ACCOMMODATE A SINGLE
<br />! �� 2" NOMINAL DIAM.
<br />FIGURE 9.1 FIGURE 9.2
<br />SLOPE NOT GREATER THAN 1 UNIT VERTICAL IN 20 UNITS HORIZONTAL (5% SLOPE).
<br />D. RECESSED DOOR MATS SHALL BE LEVEL WITH THE ADJACENT SURFACE AND BE ADEQUATELY ANCHORED TO
<br />WHEELCHAIR IS 30" BY 48". THE CLEAR FLOOR SPACE FOR WHEEL CHAIRS MAY BE POSITIONED FOR FORWARD OR
<br />ACCESSIBLE SINGLE ACCOMMODATION ACCESSIBLE SINGLE ACCOMMODATION
<br />PREVENT INTERFERENCE WITH WHEELCHAIR TRAFFIC.
<br />PARALLEL APPROACH TO AN OBJECT U.N.O.. THE CLEAR FLOOR OR GROUND SPACE FOR WHEELCHAIRS MAY BE A
<br />WALL OR PARTITION
<br />TOILET WITH SIDE OUT -SWING DOOR TOILET WITH SIDE IN -SWING DOOR
<br />PART OF THE KNEE SPACE REQUIRED UNDER SOME OBJECTS.
<br />2. RELATIONSHIP R MANEUVERING CLEARANCES TO WHEELCHAIR SPACES ONE FULL UNOBSTRUCTED SIDE OF THE
<br />CLEAR FLOOR OR GROUND SPACE FOR A WHEELCHAIR SHALL ADJOIN OR OVERLAP AN ACCESSIBLE ROUTE OR
<br />CONTROLS & O P E RATION
<br />17
<br />GRAB BARS & SHOWER S EAT
<br />13
<br />TOILET ROOM LAYOUT
<br />9
<br />�
<br />GENERAL NOTES
<br />1
<br />ADJOIN ANOTHER WHEELCHAIR CLEAR FLOOR OR GROUND SPACE. IF A CLEAR FLOOR SPACE IS LOCATED IN AN
<br />LIMITED T B E TIONS 1117A, 1119A, 1121A AND 11 B-DIVISION 4.
<br />ALCOVE OR OTHERWISE CONFINED ON ALL OR PART OF THREE SIDES, ADDITIONAL MANEUVERING CLEARANCES
<br />SHALL BE PROVIDED AS FOLLOWS:
<br />SANITARY FACILITY SIGNS SHALL COMPLY WITH CBC SECTIONS 1127A.7 AND 11 B-703.
<br />TOILET ROOM FIXTURES AND ACCESSORIES. SHALL COMPLY WITH CBC SECTIONS 1127A.8, 11 B-603 & 11 B-604
<br />WATER CLOSETS REQUIRED TO BE ACCESSIBLE SHALL COMPLY WITH CBC SECTION 1127A.2.1, 1127A.2.3, ICC A117.1-09
<br />0" CLR. 36" CLR. 48" CLR. 60" CLR.
<br />„ ADDITIONAL „
<br />30 2 48
<br />CALIFORNIA'S STANDARDS FOR SIGNAGE ARE MORE STRINGENT THAN SECTION 4.30 OF THE ADA STANDARDS FOR
<br />A. TOWEL, SANITARY NAPKINS, WASTE RECEPTACLES. WHERE TOWEL, SANITARY NAPKINS, WASTE
<br />A. WATER CLOSET FIXTURES LOCATED IN ACCESSIBLE WATER CLOSET COMPARTMENTS SHALL BE POSITIONED
<br />WITH A WALL OR PARTITION TO THE REAR AND TO ONE SIDE. THE CENTERLINE OF THE ACCESSIBLE WATER
<br />A. GENERAL. WHEN A BUILDING OR A PORTION OF A BUILDING IS REQUIRED TO BE ACCESSIBLE OR ADAPTABLE,
<br />AN A E SIBLE ROUTE SHALL BE PROVIDED TO ALL PORTIONS OF THE BUILDING, ACCESSIBLE BUILDING
<br />MANEUVERING
<br />ACCESSIBLE DESIGN. THE INFORMATION PROVIDED WITH IN THIS DETAIL IS INTENDED TO SHOW THE MINIMUM
<br />RECEPTACLES AND OTHER SIMILAR DISPENSING AND DISPOSAL FIXTURES ARE PROVIDED, AT LEAST ONE OF
<br />CLOSET SHALL BE 18" FROM THE SIDE WALL OR PARTITION.
<br />ENTRANCES, TO COVERED MULTIFAMILY DWELLING UNITS AND BETWEEN THE BUILDING AND THE PUBLIC WAY.
<br />SPACE
<br />N
<br />SIGNAGE REQUIRED AT SANITARY FACILITY DOORS ONLY TO OBTAIN A BUILDING PERMIT. IDENTIFICATION,
<br />DIRECTIONAL AND INFORMATION SIGNS ARE NOT PART OF THE ARCHITECT'S SCOPE OF WORK.
<br />EACH TYPE SHALL BE LOCATED WITH ALL OPERABLE PARTS, INCLUDING COIN SLOTS, WITHIN 40" FROM
<br />FINISHED FLOOR. A PATH OF TRAVEL NOT LESS THAN 36" IN CLEAR WIDTH SHALL BE PROVIDED TO THESE
<br />ACCESSORIES.
<br />B. ACCESSIBLE WATER CLOSETS SHALL BE PROVIDED A CLEAR FLOOR SPACE AND MANEUVERING SPACE PER
<br />DETAILS 8 AND 9 ON THIS SHEET.
<br />C. THE SEAT HEIGHT OF A WATER CLOSET ABOVE FINISH FLOOR SHALL BE 17" MINIMUM AND 19" MAXIMUM
<br />1/2" MAX. PILE THICKNESS �.
<br />ALL WALKS, HALLS, CORRIDORS, AISLES, SKYWALKS, TUNNELS AND OTHER SPACES THAT ARE PART OF THE
<br />ACCESSIBLE ROUTE SHALL COMPLY WITH THE APPLICABLE PROVISIONS OF THE APPLICABLE CODES. AT LEAST
<br />ONE ACCESSIBLE ROUTE WITHIN THE BOUNDARY OF THE SITE SHALL BE PROVIDED FROM THE PUBLIC
<br />TRANSPORTATION STOPS, ACCESSIBLE PARKING, ACCESSIBLE PASSENGER LOADING ZONES AND PUBLIC
<br />A _
<br />u, __ _
<br />1
<br />' A
<br />A. ALL ACCESSIBLE TOILET AND BATHING FACILITIES SHALL BE IDENTIFIED BY THE "INTERNATIONAL SYMBOL OF
<br />ACCESSIBILITY. SIGNS NEED NOT BE PROVIDED FOR FACILITIES WITHIN A DWELLING UNIT OR GUEST ROOM.
<br />B. TOILET PAPER DISPENSERS. SEE DETAIL 10 OF THIS SHEET. SHALL BE LOCATED ON A WALL OR PARTITION
<br />CLOSEST TO THE WATER CLOSET WITHIN 7" MINIMUM AND 9" MAXIMUM IN FRONT OF THE WATER CLOSET
<br />MEASURED TO THE TOP OF THE SEAT. SEATS SHALL NOT BE SPRUNG TO RETURN TO A LIFTED POSITION. SEATS
<br />SHALL BE 2" HIGH MAXIMUM.
<br />�
<br />STREETS OR SIDEWALKS TO THE ACCESSIBLE BUILDING ENTRANCE THEY SERVE. THE ACCESSIBLE ROUTE
<br />, ,
<br />SHALL, TO THE MAXIMUM EXTENT FEASIBLE, COINCIDE WITH THE ROUTE FOR THE GENERAL PUBLIC AND OTHER
<br />�_ _„ '�_ _y �- _____\ __,; _________
<br />B. DOORWAYS LEADING TO SANITARY FACILITIES SHALL BE IDENTIFIED BY A GEOMETRIC SYMBOL. GEOMETRIC
<br />MEASURED FROM THE CENTERLINE OF THE DISPENSER. THE OUTLET OF THE DISPENSER SHALL BE BELOW
<br />D. GRAB BARS FOR WATER CLOSETS SHALL COMPLY WITH DETAIL 13 OF THIS SHEET. GRAB BARS SHALL BE
<br />BUILDING RESIDENTS. ACCESSIBLE ROUTES SHALL NOT PASS THROUGH KITCHENS, STORAGE ROOMS,
<br />/
<br />SYMBOLS SHALL BE CENTERED HORIZONTALLY ON THE DOOR AT A HEIGHT OF 58" MIMUMUM TO 60" MAXIMUM
<br />ABOVE THE FINISH FLOOR OR GROUND SURFACE MEASURED TO THE CENTER OF THE SYMBOL. WHEN A DOOR
<br />AND NOT BEHIND THE GRAB BAR, 19" MINIMUM ABOVE THE FINISH FLOOR. DISPENSERS SHALL NOT BE OF A
<br />TYPE THAT CONTROLS DELIVERY OR THAT DOES NOT ALLOW CONTINUOUS PAPER FLOW.
<br />PROVIDED ON THE SIDE WALL CLOSEST TO THE WATER CLOSET AND ON THE REAR WALL AS INDICATED BELOW.
<br />E. FLUSH CONTROLS SHALL BE HAND OPERATED OR AUTOMATIC. HAND OPERATED CONTROLS SHALL COMPLY
<br />IF PILE HEIGHT
<br />EXCEEDS THEN EXPOSED EDGE \_ I1 FIRM PAD
<br />RESTROOMS, CLOSETS OR OTHER SPACES USED FOR SIMILAR PURPOSES EXCEPT WITHIN AN INDIVIDUAL
<br />DWELLING UNIT. ACCESSIBLE ROUTES SHALL BE PROVIDED AS FOLLOWS:
<br />1. WHERE MORE THAN ONE ROUTE OF TRAVEL IS PROVIDED, ALL ROUTES SHALL BE ACCESSIBLE.
<br />IS PROVIDED THE SYMBOL SHALL BE MOUNTED WITHIN 1 INCH OF THE VERTICAL CENTERLINE OF THE DOOR.
<br />C. MIRRORS. WHERE PROVIDED AT LEAST ONE MIRROR SHALL BE ACCESSIBLE. MIRRORS LOCATED ABOVE
<br />W F
<br />ITH DETAIL 17 OF THIS SHEET EXCEPT THAT THEY SHALL BE LOCATED 44 INCHES MAXIMUM ABOVE THE LOOR.
<br />EDGES MUST HAVE
<br />ST
<br />- - - - - - - ---- - - - - - - ----- -
<br />- - - - - - - - -- - - - - - - - - -- - - - -
<br />D. SURFACES FOR WHEELCHAIR SPACES GROUND AND FLOOR SURFACES ALONG ACCESSIBLE ROUTES, AND IN
<br />EDGES OF ACCESSIBILITY SIGNS SHALL BE ROUNDED, CHAMFERED OR EASED. CORNERS SHALL HAVE A
<br />MINIMUM RADIUS OF 1/8".
<br />LAVATORIES OR COUNTERTOPS SHALL BE INSTALLED WITH THE BOTTOM EDGE OF THE REFLECTING
<br />SURFACE 40" ABOVE THE FINISH FLOOR OR GROUND. MIRRORS NOT LOCATED ABOVE LAVATORIES OR
<br />F. TOILET PAPER DISPENSERS SHALL BE LOCATED AS INDICATED BELOW AND PER DETAIL 14 OF THIS SHEET.
<br />G. ACCESSIBLE WATER CLOSETS SHALL BE PROVIDED A CLEAR FLOOR SPACE AND MANEUVERING SPACE PER
<br />BEVELED TRIM �'
<br />� �
<br />2. AT LEAST ONE ACCESSIBLE ROUTE SHALL CONNECT ACCESSIBLE BUILDING OR FACILITY ENTRANCES WITH
<br />ALL ACCESSIBLE SPACES , ELEMENTS AND COVERED MULTIFAMILY DWELLING UNITS.
<br />3. AN ACCESSIBLE ROUTE SHALL CONNECT AT LEAST ONE ACCESSIBLE PRIMARY ENTRANCE OF EACH
<br />1. MEN'S SANITARY FACILITIES SHALL BE IDENTIFIED WITH AN EQUILATERAL TRIANGLE 1/4" THICK WITH
<br />COUNTERTOPS SHALL BE INSTALLED WITH THE BOTTOM EDGE OF THE REFLECTING SURFACE 35" MAXIMUM
<br />DETAILS 8 AND 9 ON THIS SHEET.
<br />2
<br />ACCESSIBLE ROOMS AND SPACES, INCLUDING FLOORS, WALKS, RAMPS ,STAIRS AND CURB RAMPS SHALL BE STABLE,
<br />EDGES 12" LONG AND A VERTEX POINTING UP. THE TRIANGLE SYMBOL SHALL CONTRAST WITH THE
<br />ABOVE THE FINISH FLOOR.
<br />��
<br />COVERED MULTIFAMILY DWELLING UNIT WITH INTERIOR AND EXTERIOR SPACES AND FACILITIES THAT
<br />FIRM, SLIP RESISTANT AND SHALL COMPLY WITH THE FOLLOWING:
<br />DOOR , EITHER LIGHT ON A DARK BACKGROUND OR DARK ON A LIGHT BACKGROUND.
<br />D. COAT HOOKS, SHELVES AND MEDICINE CABINETS. COAT HOOKS SHALL BE LOCATED WITHIN ONE OF THE
<br />\ 1/i - TRANSITION TRIM
<br />SERVE THE UNIT
<br />4. WHERE ELEVATORS ARE PROVIDED FOR VERTICAL ACCESS ONLY ONE IS REQUIRED, HOWEVER ALL
<br />1. CHANGES IN LEVEL, UP TO 1/4" MAY BE VERTICAL AND WITHOUT EDGE TREATMENT. CHANGES IN LEVEL BETWEEN
<br />2. WOMEN'S SANITARY FACILITIES SHALL BE IDENTIFIED WITH A CIRCLE 1/4" THICK AND 121, IN DIAMETER
<br />REACH RANGES IDENTIFIED ON DETAIL 22 ON THIS SHEET. SHELVES SHALL BE LOCATED 40" MINIMUM AND
<br />54"MIN.
<br />---
<br />ELEVATORS PROVIDED SHALL BE ACCESSIBLE.
<br />1/4" AND 1/2" SHALE BE BEVELED WITH A SLOPE NO GREATER THAN 1 UNIT VERTICAL IN 2 UNITS HORIZONTAL.
<br />AND A VERTEX POINTING UP. THE CIRCLE SYMBOL SHALL CONTRAST WITH THE DOOR , EITHER LIGHT ON
<br />48" MAXIMUM ABOVE THE FINISH FLOOR. MEDICINE CABINETS SHALL BE LOCATED WITH A USABLE SHELF NO
<br />B. FLOORING. SHALL COMPLY WITH THE REQUIREMENTS OF DETAIL 22, ITEM D OF THIS SHEET.
<br />CHANGES IN LEVEL GREATER THAN 112"MUST BE ACCOMPLISHED BY MEANS OF A RAMP, ELEVATOR OR PLATFORM
<br />A DARK BACKGROUND OR DARK ON A LIGHT BACKGROUND.
<br />HIGHER THAN 44" MAXIMUM ABOVE FINISH FLOOR.
<br />39" - 41"
<br />C. RECESSED DOOR MATS. SHALL COMPLY WITH THE REQUIREMENTS OF DETAIL 6 OF THIS SHEET.
<br />LIFT.
<br />3. UNISEX SANITARY FACILITIES SHALL BE IDENTIFIED BY A CIRCLE 1/4" THICK AND 12" IN DIAMETER WITH A
<br />E. SPACES ALLOWANCES AND REACH RANGES IN COMMON USE AREAS. SEE DETAIL 22 ON THIS SHEET FOR THE
<br />INTERIOR MATERIAL CHANGES
<br />D. PRIMARY ENTRANCES AND GROUND FLOOR EXITS. ALL ENTRANCES AND ALL EXTERIOR GROUND FLOOR EXITS
<br />2. IF CARPET OR CARPET TILE IS USED ON A GROUND OR FLOOR SURFACE, IT SHALL BE SECURELY ATTACHED; HAVE
<br />1/4" THICK TRIANGLE SUPERIMPOSED ON THE CIRCLE AND WITHIN THE 121, DIAMETER. THE TRIANGLE
<br />REQUIRED CLEAR SPACE, ALLOWABLE REACH RANGES AND REQUIREMENTS FOR CONTROLS AND
<br />36" MIN. 12" MAX. 42"MIN.
<br />A. MATERIAL CHANGES IN HEIGHT AT INTERIOR DOOR THRESHOLDS SHALL NOT EXCEED 1/2".
<br />SHALL BE ACCESSIBLE.
<br />E. SEPARATE DWELLING UNIT ENTRANCES. WHEN A GROUND -FLOOR DWELLING UNIT OF A BUILDING HAS A
<br />FIRM CUSHION, PAD OR BACKING OR NO CUSHION, PAD OR BACKING; AND HAVE A LEVEL LOOP, TEXTURED LOOP,
<br />SYMBOL SHALL CONTRAST WITH THE CIRCLE SYMBOL, EITHER LIGHT ON A DARK BACKGROUND OR DARK
<br />OPERATING MECHANISMS.
<br />B. THRESHOLDS WITH A CHANGE IN HEIGHT OF NOT MORE THAN 1/4" MAYBE VERTICAL.
<br />SEPARATE ENTRANCE, EACH SUCH GROUND -FLOOR DWELLING UNIT SHALL BE SERVED BY AN ACCESSIBLE
<br />LEVEL -CUT PILE, OR LEVEL-CUT/UNCUT PILE TEXTURE. THE MAXIMUM PILE HEIGHT SHALL BE 1/2". EXPOSED EDGES
<br />ON A LIGHT BACKGROUND. THE CIRCLE SYMBOL SHALL CONTRAST WITH THE DOOR , EITHER LIGHT ON A
<br />12" MIN. 24" MIN.
<br />z
<br />ROUTE EXCEPT WHERE THE SITE TERRAIN PROHIBITS AN ACCESSIBLE ROUTE (SEE CBC SECTION 1150A).
<br />OF THE CARPET SHALL BE FASTENED TO THE FLOOR SURFACES AND HAVE TRIM ALONG THE ENTIRE LENGTH OF
<br />DARK BACKGROUND OR DARK ON A LIGHT BACKGROUND.
<br />TOILET
<br />1= �
<br />F. MULTIPLE ENTRANCES. ONLY ONE ENTRANCE TO COVERED MULTIFAMILY BUILDINGS IS REQUIRED TO BE
<br />THE EXPOSED EDGE. CARPET EDGE TRIM SHALL COMPLY WITH ITEM 1 ABOVE
<br />3. ABRUPT CHANGES IN LEVEL ALONG ANY ACCESSIBLE ROUTE SHALL NOT EXCEED 112". WHEN CHANGES IN LEVEL
<br />PAPER
<br />�
<br />> SQ BEVEL
<br />ACCESSIBLE TO ANY ONE GROUND FLOOR OF A BUILDING, EXCEPT IN CASES WHERE AN INDIVIDUAL DWELLING
<br />UNIT HAS A SEPARATE EXTERIOR ENTRANCE. WHERE THE BUILDING CONTAINS CLUSTERS OF DWELLING UNITS
<br />DISPENSER
<br />_
<br />� 2
<br />DO OCCUR, THEY SHALL BE BEVELED WITH A SLOPE NO GREATER THAN 1 UNIT VERTICAL IN 2 UNITS HORIZONTAL.
<br />CHANGES IN LEVEL NOT EXCEEDING 1/4" MAY BE VERTICAL.
<br />4. IF GRATINGS ARE LOCATED IN WALKING SURFACES, THEN THEY SHALL BE LIMITED TO SPACES NO GREATER THAN
<br />i
<br />FINISH FLOOR EVEN
<br />1 �
<br />WITH EACH CLUSTER SHARING A DIFFERENT EXTERIOR ENTRANCE, MORE THAN ONE ENTRANCE MAY BE
<br />REQUIRED TO BE ACCESSIBLE AS DETERMINED BY ANALYSIS OF THE SITE TERRAIN. IN EVERY CASE, THE
<br />ACCESSIBLE ENTRANCE SHALL BE ON AN ACCESSIBLE ROUTE TO THE COVERED MULTIFAMILY DWELLING UNIT
<br />112"WIDE IN ONE DIRECTION . IF GRATINGS HAVE ELONGATED OPENINGS, THEY SHALL BE PLACED SO THAT THE
<br />O _ _ • •
<br />o =' 24"MIN.
<br />COMPRESSED CARPET 1/2" �.
<br />IT SERVES.
<br />LONG DIMENSION IS PERPENDICULAR TO THE DOMINATE DIRECTION OF TRAVEL.
<br />'� o o
<br />`'
<br />MAX. BELOW THRESHOLD
<br />G. INTERIOR WIDTHS AND LENGTHS. SHALL COMPLY WITH THE REQUIREMENTS OF DETAIL 22, ITEM A OF THIS
<br />=
<br />DOOR THRESHOLD
<br />HEET. IF A PER N IN A WHEEL CHAIR MUST MAKE A TURN AROUND A CORNER OR OBSTRUCTION THE
<br />E. REACH RANGES SHALL COMPLY WITH THE FOLLOWING FIGURES:
<br />M M �,
<br />X
<br />a � w
<br />ACCESSIBLE ROUTE SHALL COMPLY WITH DETAIL 22, ITEM B OF THIS SHEET.
<br />"X"
<br />a,
<br />�, M M
<br />,1,
<br />mi m
<br />H. CHANGES IN LEVEL NOT EXCEEDING 1/2". ABRUPT CHANGES IN LEVEL ALONG ANY ACCESSIBLE ROUTE SHALL
<br />_
<br />i,_o„
<br />`' M
<br />� T' _ 9" � �
<br />" -
<br />�� -�
<br />24 - m
<br />MAT CARPETING MUST CONSIST OF:
<br />A. LEVEL LOOP
<br />NOT EXCEED 1/2". WHEN CHANGES IN LEVEL DO OCCUR, THEY SHALL BE BEVELED WITH A SLOPE NO GREATER
<br />THAN 1 UNIT VERTICAL IN 2 UNITS HORIZONTAL (50% SLOPE). CHANGES IN LEVEL NOT EXCEEDING 1/4" MAY BE
<br />VERTICAL.
<br />N �o Q . �
<br />MEWS DOOR WOMEN'S DOOR UNISEX DOOR
<br />B. TEXTURED LOOP
<br />I. CHANGES IN LEVEL GREATER THAN 1/2". CHANGES IN LEVEL GREATER THAN 1/2" SHALL BE MADE BY MEANS OF
<br />o
<br />z
<br />o � � -- = = o w
<br />SIGNAGE SIGNAGE SIGNAGE
<br />C. LEVEL CUT PILE
<br />D. LEVEL CUTIUNCUT PILE
<br />A SLOPED SURFACE WITH A SLOPE NOT GREATER THAN 1 UNIT VERTICAL IN 20 UNITS HORIZONTAL (5 /° SLOPE),
<br />OR A CURB RAMP PER CBC SECTION 1112A, A RAMP PER CBC SECTION 1114A EXTERIOR RAMPS OR 1122A
<br />� 4 = � � � - > - c- - �,
<br />_ - " x
<br />18" REAR WALL SIDE WALL
<br />INTERIOR RAMPS, ELEVATOR PER CBC SECTION 3003 OR PLATFORM WHEELCHAIR LIFT PER CBC SECTION
<br />1124A. WHEN STAIRS ARE LOCATED ALONG OR ADJACENT TO AN ACCESSIBLE ROUTE THEY SHALL COMPLY
<br />PARALLEL APPROACH SIDE REACH FORWARD APPROACH FORWARD REACH
<br />WITH CBC SECTION 1115A EXTERIOR STAIRWAYS OR 1123A INTERIOR STAIRWAYS.
<br />' THE TOP OF WASHING MACHINES AND CLOTHES DRYERS ARE PERMITTED TO BE 36" MAXIMUM ABOVE THE FINISH FLOOR.
<br />SPACE & REACH RQMTS.
<br />22
<br />SANITARY FACILITY SIGNAGE
<br />18
<br />FIXTURES AND ACCESSORIES
<br />14
<br />WATER CLOSET
<br />10
<br />LANDINGS & THRESHOLDS
<br />6
<br />ACCESSIBLE ROUTE
<br />2
<br />COMMON ACCESSIBLE LAUNDRY ROOMS SHALL COMPLY WITH CBC SECTIONS 1127A.10 AND 11 B-611
<br />SHOWERS REQUIRED TO BE ACCESSIBLE SHALL COMPLY WITH CBC SECTIONS 1127A.5.3 AND 11 B-608.
<br />ACCESSIBLE URINALS SHALL COMPLY WITH CBC SECTION 1127A.2.4 AND 11 B-605.
<br />MULTIPLE -ACCOMMODATION TOILET FACILITIES SHALL COMPLY WITH CBC SECTIONS 1127A.2.1 AND 11 B-604.
<br />DOORS THAT PROVIDE ACCESS TO COMMON USE AREAS SHALL COMPLY WITH SECTION 1126A AND 11 B-404. THIS SHEET FOR
<br />LANDINGS AND THRESHOLDS. THE COMMON USE OR PUBLIC SIDE OF PRIMARY ACCESS DOORS TO DWELLING UNITS SHALL
<br />WHERE COMMON USE LAUNDRY ROOMS ARE PROVIDED AT LEAST ON TYPE OF APPLIANCE PROVIDED IN EACH
<br />A. SHOWERS SHALL BE CONSISTENT WITH ONE OF THE FOLLOWING SIZES AND SHALL BE MEASURED FROM THE FACE OF WALL SURFACES:
<br />A. URINALS SHALL BE FLOOR MOUNTED STALL TYPE OR WALL HUNG WITH THE RIM 17" MAXIMUM ABOVE THE
<br />)1/2"
<br />A. TURNING SPACE OF SUFFICIENT SIZE TO INSCRIBE A CIRCLE WITH A DIAMETER NOT LESS THAN 60" OR A
<br />COMPLY WITH NOTES F AND G BELOW.
<br />LAUNDRY AREA SHALL BE ACCESSIBLE AND SHALL BE ON AN ACCESSIBLE ROUTE. SUCH APPLIANCES SHALL
<br />INCLUDE CLOTHES WASHING MACHINES, DRYERS, SOAP DISPENSERS AND ANY RELATED FEATURES SUCH AS
<br />1. ROLL -IN SHOWER 60" MIN. IN WIDTH BY 30" MIN. IN DEPTH WITH A FULL OPENING WIDTH ON THE LONG THE SIDE SEE FIGURE 16.1 BELOW. 27" MAX.
<br />FINISH FLOOR OR GROUND. URINALS SHALL BE 13 DEEP MINIMUM MEASURED FROM THE OUTER FACE OF
<br />T-SHAPED SPACE SHALL BE PROVIDED WITHIN THE TOILET FACILITY. THE WHEECHAIR TURNING SPACE SHALL
<br />A. DOORWAYS SHALL PERMIT THE INSTALLATION OF A DOOR NOT LESS THAN 36 IN WIDTH NOT LESS THAN 80 IN HEIGHT
<br />WASH SINKS TABLES AND STORAGE AREAS.
<br />2. ALTERNATE ROLL -IN SHOWER, 60" MIN. IN WIDTH BY 36" IN DEPTH WITH AN ENTRANCE OPENING WIDTH OF 36", SEE FIGURE 16.2 BELOW.
<br />19 MIN.
<br />"
<br />THE URINAL RIM TO THE BACK OF THE FIXTURE.
<br />1
<br />COMPLY WITH SECTION 1138A.1.3.OTHER THAN THE DOOR TO THE ACCESSIBLE WATER CLOSET COMPARTMENT,
<br />AND PROVIDE A CLEAR OPENING OF NOT LESS THAN 32 IN WIDTH MEASURED WITH THE DOOR OR DOORS POSITIONED
<br />WHERE LAUNDRY ROOMS ARE PROVIDED ON FLOORS OF AN ELEVATOR BUILDING, EACH LAUNDRY ROOM SHALL
<br />3. ALTERNATE ROLL -IN SHOWER WITH OPTIONAL ENCLOSURE 60 MIN. IN WIDTH BY 36 MIN. IN DEPTH AS LONG AS THE ENTRANCE
<br />C. WHERE URINALS ARE PROVIDED, AT LEAST ONE SHALL HAVE A CLEAR FLOOR SPACE OF 30 X 48 IN FRONT OF
<br />A DOOR IN ANY POSITION MAY ENCROACH INTO THIS SPACE BY NOT MORE THAN 12 .
<br />AT AN ANGLE OF 90-DEGREES FROM THE CLOSED POSITION.
<br />OPENING WIDTH IS A MIN. 36", SEE FIGURE 16.3 BELOW.
<br />THE URINAL TO ALLOW FORWARD APPROACH. THE CLEAR FLOOR SPACE SHALL COMPLY WITH DETAIL 22 OF
<br />B. DOORS SHALL NOT SWING INTO THE FLOOR SPACE REQUIRED FOR ANY FIXTURE. REQUIRED CLEAR FLOOR
<br />B, DOORS SHALL BE CAPABLE OF OPENING AT LEAST 90 DEGREES..
<br />BE ACCESSIBLE. WHERE THERE IS ONE LAUNDRY ROOM ON A GROUND FLOOR IN EACH BUILDING EACH LAUNDRY
<br />B. THRESHOLDS IN ROLL -IN TYPE SHOWERS SHALL BE 1/2 HIGH MAX. CHANGES IN LEVEL UP T0114 MAY BE VERTICAL AND WITHOUT EDGE
<br />THIS SHEET.
<br />SPACE CLEARANCE AT FIXTURES AND TURNING SPACE SHALL BE PERMITTED TO OVERLAP. SEE FIGURE 8.2-B
<br />C. A PAIR OF DOORS MANUAL OR AUTOMATIC MUST HAVE AT LEAST ONE LEAF THAT PROVIDES A CLEAR WIDTH OF NOT
<br />ROOM SHALL BE ACCESSIBLE. WHERE THERE IS A LAUNDRY ROOM ON THE GROUND FLOOR OF A BUILDING AND
<br />TREATMENT. CHANGES IN LEVEL BETWEEN 114"AND 112"SHALL BE BEVELED WITH A SLOPE NO GREATER THAN ONE UNIT VERT. IN 2 UNITS
<br />D. FLUSH CONTROLS SHALL HAND OPERATED OR AUTOMATIC. HAND OPERATED FLUSH CONTROLS SHALL
<br />BELOW ACCESSIBLE COMPARTMENT WITH SIDE IN -SWING DOOR.
<br />LESS THAN 32 MEASURED WITH THE DOOR POSITIONED AT AN ANGLE OF 90-DEGREES FROM ITS CLOSED POSITION.
<br />ANOTHER LOCATED IN A BASEMENT, IT IS ACCEPTABLE TO ONLY HAVE THE GROUND FLOOR LAUNDRY
<br />HORIZ.
<br />COMPLY WITH DETAIL 17 OF THIS SHEET EXCEPT THAT THE FLUSH CONTROL SHALL BE MOUNTED AT A
<br />C. PROVIDE A MINIMUM OF ONE ACCESSIBLE WATER CLOSET IN COMPLIANCE WITH THE REQUIREMENTS WITHIN
<br />AT DOUBLE EGRESS DOORS EACH LEAF MUST PROVIDE THE CLEAR WIDTH.
<br />ACCESSIBLE.
<br />C. SHOWER COMPARTMENT FLOOR SURFACES SHALL BE STABLE, FIRM AND SLIP RESISTANT. THE MAXIMUM SLOPE OF THE FLOOR SHALL BE
<br />MAXIMUM HEIGHT OF 44" ABOVE FINISH FLOOR.
<br />THIS DETAIL AND DETAIL 10 ON THIS SHEET. PROVIDE AT LEAST 5 PERCENT OF LAVATORIES, BUT NOT LESS
<br />D. THE WIDTH OF ANY COMPONENT OF THE EGRESS SYSTEM SHALL NOT BE LESS THAN THE MINIMUM WIDTH REQUIRED
<br />A. THERE SHALL BE A MINIMUM CLEAR SPACE 30" PERPENDICULAR BY 48" PARALLEL IN FRONT OF CLOTHES
<br />1/4" PER FOOT IN ANY DIRECTION. WHEN DRAINS ARE PROVIDED, GRATE OPENINGS SHALL BE 1/4" MAXIMUM AND LOCATED FLUSH WITH THE
<br />FLOOR SURFACE. I-
<br />THAN ONE LAVATORY, SHALL BE ACCESSIBLE IN COMPLIANCE WITH DETAIL 12 OF THIS SHEET.
<br />D. WATER CLOSETS REQUIRED TO BE ACCESSIBLE SHALL COMPLY WITH THE FOLLOWING:
<br />BY SECTION 1005.
<br />E. PER CBC SECTION 1010.1.5, THERE SHALL BE A FLOOR OR LANDING ON EACH SIDE OF THE DOOR. SUCH FLOOR OR
<br />WASHERS AND DRYERS REQUIRED TO BE ACCESSIBLE. THERE SHALL BE A MINIMUM CLEAR SPACE 30" BY 48"
<br />T- Y
<br />D. WHERE, WITHIN THE SAME FUNCTIONAL AREA, TWO OR MORE ACCESSIBLE SHOWERS ARE PROVIDED, THERE SHALL BE AT LEAST ONE U
<br />1. THE CENTERLINE OF THE ACCESSIBLE WATER CLOSET SHALL BE 18" MAXIMUM FROM THE SIDE WALL OR
<br />LANDING SHALL BE THE SAME ELEVATION ON EACH SIDE OF THE DOOR. LANDINGS SHALL BE LEVEL EXCEPT FOR
<br />EXTERIOR LANDINGS WHICH ARE PERMITTED TO HAVE A SLOPE NOT TO EXCEED 1/4" VERTICAL TO 12" HORIZONTAL
<br />PROVIDED FOR AT LEAST ONE TYPE OF FIXTURE OR APPLIANCE PROVIDED IN THE LAUNDRY ROOM E.G.
<br />( �
<br />i `.
<br />SHOWER CONSTRUCTED OPPOSITE HAND FROM THE OTHER OR OTHERS (THAT IS, ONE LEFT-HAND CONTROL VERSUS ONE RIGHT-HAND � � ,\ ¢
<br />PARTITION. THE CENTERLINE OF THE ACCESSIBLE WATER CLOSET LOCATED IN A AMBULATORY ACCESSIBLE
<br />(2-PERCENT SLOPE). SEE DETAIL 6 FOR ADDITIONAL INFORMATION.
<br />SOAP DISPENSERS, WASH SINKS, TABLES AND STORAGE AREAS).
<br />CONTROL). I Of
<br />30" MINIMUM
<br />COMPARTMENT, REQUIRED BY NOTE F BELOW, SHALL BE 18" FROM THE SIDE WALL OR PARTITION.
<br />F. MANEUVERING CLEARANCES AT DOORS
<br />B. CLOTHES WASHERS AND DRYERS INCLUDING STACKED CLOTHES WASHERS AND DRYERS REQUIRED TO BE
<br />ACCESSIBLE SHALL HAVE CONTROLS COIN SLOTS) WITHIN THE REACH RANGE OF A SEATED
<br />E. WATER CONTROLS SHALL BE OF A SINGLE -LEVER DESIGN, OPERABLE WITH ONE HAND, AND SHALL NOT REQUIRE TIGHT GRASPING, 1 \ c�
<br />�
<br />_y
<br />2. PROVIDE A CLEAR FLOOR SPACE AND MANEUVERING SPACE IN COMPLIANCE WITH FIGURES 8.1A, 8.1 B, 8.2A
<br />1. THE LEVEL FLOOR OR LANDING OF AN EXIT DOOR SHALL HAVE A LENGTH IN THE DIRECTION OF THE DOOR SWING
<br />(INCLUDING
<br />PINCHING OR TWISTING OF THE WRIST. THE FORCE REQUIRED TO ACTIVATE THE CONTROLS SHALL BE NO GREATER THAN 5 LBS. THE :: \ � z
<br />� ~
<br />-------------I
<br />OR 8.26 AT THE ACCESSIBLE WATER CLOSET COMPARTMENT AND FIGURE 3 WHEN A AMBULATORY
<br />OF AT LEAST 60" AND A LENGTH OPPOSITE OF THE DOOR SWING OF AT LEAST 44" MEASURED AT RIGHT ANGLES TO
<br />USER. CONTROLS SHALL BE LOCATED NO HIGHER THAN 48"AND NO LOWER THAN 15", ABOVE THE FINISH
<br />CENTERLINE OF THE CONTROLS SHALL BE LOCATED 39" TO 41" ABOVE THE SHOWER FLOOR AND LOCATED WITHIN THE SHOWER PER THE =
<br />I - z
<br />�
<br />ACCESSIBLE COMPARTMENT IS REQUIRED.
<br />THE PLANE OF THE DOOR IN ITS CLOSED POSITION. SEE FIGURES BELOW.
<br />FLOOR MEASURED TO THE CENTER OF THE GRIP. IF THE REACH IS OVER AN OBSTRUCTION FOR EXAMPLE, A
<br />(
<br />FIGURES WITHIN. . C ) �
<br />M O
<br />i r
<br />E. ACCESSIBLE WATER CLOSET COMPARTMENT DOORS SHALL COMPLY WITH THE FOLLOWING:
<br />2. THE WIDTH OF LEVEL AREA ON THE SIDE TO WHICH THE DOOR SWINGS SHALL EXTEND AT LEAST 18" PAST THE
<br />WASHER OR DRYER BETWEEN 20' AND 25 IN DEPTH THE MAXIMUM HEIGHT IS REDUCED TO 44 FOR
<br />"
<br />z
<br />-
<br />F. A SHOWER SPRAY UNIT WITH A HOSE 59" INCHES LONG MINIMUM THAT CAN BE USED BOTH AS A FIXED POSITION SHOWER HEAD AND AS A � z _ �
<br />I I
<br />I I 1
<br />1. THE COMPARTMENT DOOR SHALL BE EQUIPPED WITH AN AUTOMATIC CLOSING DEVISE, AND SHALL HAVE A
<br />STRIKE EDGE OF THE DOOR FOR INTERIOR DOORS AND AT LEAST 24" PAST THE STRIKE EDGE OF THE DOOR FOR
<br />EXTERIOR DOORS.
<br />FORWARD APPROACH, OR 46" FOR SIDE APPROACH, PROVIDED THAT THE OBSTRUCTION IS NO MORE THAN
<br />24" IN DEPTH. CONTROLS THAT DO NOT SATISFY THESE SPECIFICATIONS ARE ACCEPTABLE, PROVIDED THAT
<br />HAND HELD SHOWER SHALL BE PROVIDED. THE SHOWER SPRAY UNIT SHALL HAVE AN ONIOFF CONTROL WITH A NON POSITIVE SHUT OFF. - a� "
<br />M _ 6" MAX. O
<br />\ i I
<br />� ,
<br />I 1 1
<br />CLEAR, UNOBSTRUCTED OPENING WIDTH OF 32"WHEN LOCATED AT THE END AND 34"WHEN LOCATED AT
<br />3. THE FOLLOWING PROVISIONS SHALL APPLY TO SWINGING DOORS WITH A FRONT APPROACH:
<br />PULL SIDE _
<br />I + D00 2"
<br />I 18" AT INTERIOR DOORS
<br />COMPARABLE CONTROLS OR OUTLETS, THAT PROVIDE THE SAME FUNCTIONS, ARE PROVIDED WITHIN THE
<br />SAME AREA AND ARE ACCESSIBLE. CONTROLS SHALL BE OPERABLE WITH ONE HAND AND NOT REQUIRE
<br />IF AN ADJUSTABLE HEIGHT SHOWER HEAD OR A VERTICAL BAR IS USED, THE BAR SHALL BE INSTALLED SO AS NOT TO OBSTRUCT THE USE M _ .
<br />M -
<br />OF GRAB BARS. SHOWER SPRAY UNITS SHALL DELIVER WATER THAT IS 120'F MAXIMUM. WHERE SUBJECT TO EXCESSIVE VANDALISM, TWO O
<br />FIXED SHOWER HEADS SHALL BE INSTALLED INSTEAD OF A HAND-HELD SPRAY UNIT IN FACILITIES THAT ARE NOT TRANSIENT LODGING ~
<br />� i I
<br />I I
<br />� I I
<br />1
<br />z I I 1
<br />I �� I 1
<br />THE SIDE WITH THE DOOR POSITIONED AT AN ANGLE OF 90 DEGREES FROM ITS CLOSED POSITION. SEE ALL
<br />FIGURES BELOW.
<br />2. THE INSIDE AND OUTSIDE OF THE COMPARTMENT DOOR SHALL BE EQUIPPED WITH ALOOP OR U-SHAPED
<br />TIGHT GRASPING, PINCHING OR TWISTING OF THE WRIST. SEE DETAIL 22 ON THIS SHEET.
<br />GUEST ROOMS. EACH SHOWER HEAD SHALL BE INSTALLED SO IT CAN BE OPERATED INDEPENDENTLY OF THE OTHER AND SHALL HAVE
<br />co I i
<br />PARTITION
<br />HANDLE IMMEDIATELY BELOW THE LATCH. THE LATCH SHALL BE FLIP -OVER STYLE, SLIDING OR OTHER
<br />I WIDTH MI
<br />MIN.
<br />C. WASHING MACHINES AND CLOTHES DRYERS IN ACCESSIBLE COMMON USE LAUNDRY ROOMS SHALL BE
<br />FRONT LOADING.
<br />SWIVEL ANGLE ADJUSTMENTS, BOTH VERTICALLY AND HORIZONTALLY. J, 60" MIN. FINISH TO FINISH CLEAR
<br />G. A FOLDING SEAT SHALL BE SIZED AND LOCATED AS SHOWN BELOW. SEE DETAIL 13 THIS SHEET FOR SEAT STRENGTH AND MOUNTING
<br />I I
<br />I i I OR WALL I I
<br />I I 1
<br />WHEN
<br />HARDWARE NOT REQUIRING THE USER TO GRASP OR TWIST.
<br />3. EXCEPT FOR DOOR -OPENING WIDTHS AND DOOR SWINGS, A CLEAR, UNOBSTRUCTED ACCESS OF NOT LESS
<br />o �
<br />co -
<br />z 24 AT EXTERIOR DOORS 1
<br />D. DEEP UTILITY SINKS SHALL MEET THE REQUIREMENTS FOR FAUCET CONTROLS (SEE DETAIL 12 THIS SHEET)
<br />REQUIREMENTS.
<br />I
<br />OCCURS 1
<br />THAN 44 INCHES SHALL BE PROVIDED TO WATER CLOSET COMPARTMENTS DESIGNED FOR USE BY PERSONS
<br />MIN. �
<br />AND A 30"X48"CLEAR FLOOR SPACE PARALLEL TO THE SINK SHALL BE PROVIDED.
<br />H. GRAB BARS SHALL BE LOCATED ON WALLS ADJACENT TO AND OPPOSITE THE SEAT. GRAB BARS SHALL ALSO COMPLY WITH THE DIAMETER,
<br />WITH DISABILITIES, AND THE SPACE IMMEDIATELY IN FRONT OF A WATER CLOSET COMPARTMENT SHALL NOT
<br />_ _ _ _ � =
<br />E. FOLDING TABLES SHALL BE PROVIDED WITH THE TABLE TOP BETWEEN 28" TO 34" ABOVE THE FLOOR. KNEE
<br />SPACE SHALL BE PROVIDED BELOW IN COMPLIANCE WITH DETAIL 12 THIS SHEET.
<br />SHOWER BACK CONTROL WALL ELEVATION FOR FIGURES 16.1 AND 16.3
<br />LOADING AND PROJECTION REQUIREMENTS OF DETAIL 13 ON THIS SHEET. GRAB BARS SHALL BE MOUNTED BETWEEN A MINIMUM 33" AND A
<br />MAXIMUM 36" ABOVE THE SHOWER FLOOR. L-SHAPED GRAB BARS ARE PERMISSIBLE OR MULTIPLE GRAB BARS INSTALLED AT THE SAME
<br />� � I
<br />i,/ `� i i
<br />`----- -----� I
<br />BE LESS THAN 48 INCHES AS MEASURED AT RIGHT ANGLES TO COMPARTMENT DOOR IN ITS CLOSED
<br />POSITION. MANEUVERING SPACE OUTSIDE THE COMPARTMENT DOOR SHALL COMPLY WITH DETAIL 4, NOTE
<br />z
<br />�
<br />DOOR L____�J
<br />WIDTH PUSH SIDE
<br />HEIGHT AND NO MORE THAN 6" FROM ADJACENT WALLS. GRAB BARS MAYBE MOUNTED ON WALLS ADJACENT TO AND OPPOSITE THE SEAT,
<br />z � - I
<br />F, OF THIS SHEET. MANEUVERING SPACE INSIDE THE COMPARTMENT SHALL COMPLY WITH THE THE FIGURES
<br />-
<br />BUT SHALL NOT EXTEND TO INCLUDE THAT PORTION OF WALL OVER THE SEAT. 60" MIN. FINISH TO FINISH CLEAR
<br />N � �� � L----- __J
<br />BELOW.
<br />ADDITIONAL MANEUVERING SPACE IF A DOOR
<br />I. WHEN A SOAP DISH IS PROVIDED, IT SHALL BE LOCATED ON THE CONTROL WALL AT A MAXIMUM HEIGHT OF 40"ABOVE THE SHOWER FLOOR,
<br />� -
<br />4. TOE CLEARANCE SHALL BE PROVIDED ON AT LEAST ONE SIDE PARTITION OF AT LEAST 9" HIGH AND 6" DEEP
<br />L _ J IS PROVIDED WITH BOTH CLOSER AND LATCH
<br />AND WITHIN THE 27" MAXIMUM REACH LIMITS FROM THE SEAT. BACK CONTROL WALL
<br />M o
<br />MEASURED FROM THE COMPARTMENT -SIDE FACE OF THE PARTITION, EXCLUSIVE OF PARTITION SUPPORT
<br />4. THE FOLLOWING PROVISIONS SHALL APPLY TO SWINGING DOORS WITH A HINGE SIDE APPROACH:
<br />J. ENCLOSURES, WHEN PROVIDED FOR SHOWER COMPARTMENTS, SHALL NOT OBSTRUCT CONTROLS OR TRANSFER FROM WHEELCHAIRS
<br />MEMBERS. PARTITION COMPONENTS AT TOE CLEARANCES SHALL BE SMOOTH WITHOUT SHARP EDGES OR
<br />ONTO SHOWER SEATS. - -
<br />J i ^ I
<br />ABRASIVE SURFACES. TOE CLEARANCE IS NOT REQUIRED IN COMPARTMENTS GREATER THAN 66" WIDE.
<br />F. IN LARGE TOILET ROOMS, WHERE SIX OR MORE STALLS ARE PROVIDED WITHIN A MULTIPLE- ACCOMMODATION
<br />PULL SIDE - -
<br />22" D00
<br />MIN WIDTH
<br />I
<br />EQ. EQ.
<br />TOILET ROOM, IN ADDITION TO THE WATER CLOSET COMPARTMENT REQUIRED ABOVE, PROVIDE AT LEAST ONE
<br />�
<br />z U) � z ¢
<br />27" MAX. � z w I o Q /__/ w
<br />22 23 .< M o w i Jo � I o
<br />31"CLEAR 13 112"MIN.
<br />17" MAX.
<br />AMBULATORY ACCESSIBLE COMPARTMENT. THE AMBULATORY ACCESSIBLE COMPARTMENT SHALL BE 36" WIDE
<br />WITH AN OUTWARD SWINGING SELF CLOSING DOOR AND PARALLEL GRAB BARS COMPLYING WITH DETAIL 13 OF
<br />THIS SHEET INSTALLED ON EACH SIDE WALL OF THE COMPARTMENT. SEE FIGURE 8.3 BELOW.
<br />z 1 z
<br />� �
<br />19"MIN. N = I MAXIMUM
<br />- U) F
<br />48" MIN. 48" MIN.
<br />LOCATE END DOOR DIAGONAL
<br />---- 00
<br />18" z I 1 1/4" : V-0" SLOPE
<br />`1
<br />END DOOR END DOOR
<br />MANEUVERIN TO THE WATER CLOSET MANEUVERING
<br />DOOR 36"MIN---------
<br />WIDTH PUSH SIDE
<br />LAUNDRY ROOMS
<br />2 3
<br />_ ___-_'________________ ___
<br />i � i \`. 1/2" MAX. THRESHOLD 7�'
<br />1
<br />I z F- -- I 1
<br />1 o w l� z 1 `• " CLEAR
<br />`n
<br />URINAL 11
<br />ACCESSIBLE LAVATORIES SHALL COMPLY WITH CBC SECTIONS 1127A.3,1138A.2 AND 11 B-606.
<br />___ rL r--
<br />o cw� -- -- j 1 °� o p C> _ I �o
<br />o z M � �, 1 1 o z a N - ✓ `�
<br />, - z 1 ,< ; i z > ,Y z �a'
<br />w � w .< I 1 w U_ � w ,/ `�
<br />I
<br />r-� ADDITIONAL MANEUVERING SPACE IF A DOOR
<br />�_� IS PROVIDED WITH BOTH CLOSER AND LATCH
<br />5. THE FOLLOWING PROVISIONS SHALL APPLY TO SWINGING DOORS WITH A LATCH SIDE APPROACH:
<br />STORAGE SHALL COMPLY WITH CBC SECTIONS 1127A.11 AND 11 B-811.
<br />IF FIXED STORAGE FACILITIES SUCH AS CABINETS AND SHELVES, CLOSETS AND DRAWERS ARE PROVIDED WHERE ACCESS
<br />x � 1 ��
<br />I 1 a FLOOR
<br />v M I SPACE 1
<br />LAVATORY FIXTURES, VANITIES AND BUILT-IN LAVATORIES SHALL COMPLY WITH THE FOLLOWING:
<br />A. LAVATORIES, WHEN LOCATED ADJACENT TO A SIDE WALL OR PARTITION, SHALL BE A MINIMUM OF 18" TO THE
<br />_ z J _ z �, J f /
<br />o Q J M �' o � J M " ,' I
<br />= v �_ ---� v __� ___i
<br />PULL SIDE
<br />-------� D00 24"
<br />r-------�
<br />IS REQUIRED (BY CBC SECTIONS 1.8.2.1.2 AND 1102A), AT LEAST ONE OF EACH TYPE OF FACILITY PROVIDED SHALL COMPLY
<br />= ' `.
<br />CENTERLINE OF THE FIXTURE. ALL LAVATORIES DESIGNATED TO BE ACCESSIBLE SHALL BE A MINIMUM 17" IN
<br />5g"MIN. AT / 36' MIN. 59"MIN. AT
<br />I 1 WIDTH MIN
<br />z z 1
<br />WITH THE FOLLOWING ITEMS. ADDITIONAL STORAGE MAY BE PROVIDED OUTSIDE OF THE REACH RANGES.
<br />m I -' 1 I
<br />CD I 1 I -� 1
<br />HORIZONTAL DEPTH AND MOUNTED WITH THE RIM OR COUNTER EDGE NO HIGHER THAN 34" ABOVE THE
<br />' ' DOOR PERMITTED ' ' '
<br />= 1
<br />-
<br />A. A CLEAR FLOOR SPACE AT LEAST 30" BY 48" COMPLYING WITH CBC SECTION 1138A.14 THAT ALLOWS EITHER A
<br />� z I 1 I
<br />I I � � � 1
<br />z 1 1 � z i
<br />21/2" MAX. w o--------------------------�
<br />FINI H FL RAND WITH VERTI AL LEARAN E MEA RED FR M THE B TT M APR N R TIDE
<br />S 00 C C C SU 0 0 0 0 0 OU S
<br />BOTTOM EDGE OF THE LAVATORY OF 29" REDUCING TO 27" AT A POINT LOCATED 8" BACK FROM THE FRONT
<br />FLR. MTD. W.C. WHEN DR. FLR. MTD. W.C.
<br />TO SWING OVER
<br />OR 56"MIN. AT SWINGS IN OR 56"MIN. AT
<br />HATCHED PORTION
<br />�� 1 z I I
<br />z -I
<br />1 � � 1 1
<br />FORWARD OR PARALLEL APPROACH BY A PERSON USING A WHEELCHAIR SHALL BE PROVIDED AT ACCESSIBLE
<br />0 M z_ � z
<br />EDGE. IN ADDITION, A MINIMUM 9"HIGH TOE CLEARANCE MUST BE PROVIDED EXTENDING BACK TOWARD THE
<br />WALL MTD. W.C. OF MANEUVERING WALL MTD. W.C.
<br />CO . 1 1
<br />�
<br />STORAGE FACILITIES.
<br />z 15" -16" Q w 60" MIN.
<br />o
<br />WALL TO A DISTANCE NO MORE THEN 6" FROM THE BACK WALL. THE TOE CLEARANCE SPACE MUST BE FREE
<br />CLR. FLR. SPACE SPACE CLR. FLR. SPACE
<br />DOOR 24"-------�
<br />B. ACCESSIBLE STORAGE SPACES AND CLOTHES RODS SHALL BE WITHIN AT LEAST ONE OF THE REACH RANGES
<br />_
<br />a 6" MAX. 6' M 0- a
<br />0 M � o
<br />OF EQUIPMENT AND OBSTRUCTIONS; SEE FIGURE B BELOW.
<br />B. A CLEAR FLOOR SPACE 30" BY 48" COMPLYING WITH THE FIGURES BELOW AND DETAIL 22, NOTE D, OF THIS
<br />FIGURE 8.1 A FIGURE 8.1 B
<br />ACCESSIBLE COMPARTMENT WITH ACCESSIBLE COMPARTMENT WITH
<br />WIDTH MIN L-------J
<br />PUSH SIDE
<br />SPECIFIED IN SECTION 1138A.3.
<br />C. HARDWARE FOR ACCESSIBLE STORAGE FACILITIES SHALL COMPLY WITH CBC SECTION 1138A.4. TOUCH LATCHES
<br />SHOWER SEAT o0 FIGURE 16.1 ROLL -IN SHOWER, PLAN VIEW
<br />SHEET SHALL BE PROVIDED IN FRONT OF AND CENTERED ON ACCESSIBLE LAVATORIES TO ALLOW FORWARD
<br />END OUT -SWING DOOR END IN -SWING DOOR
<br />i i ADDITIONAL MANEUVERING SPACE IF
<br />AND U-SHAPED PULLS ARE ACCEPTABLE.
<br />APPROACH. SUCH CLEAR FLOOR SPACE SHALL ADJOIN OR OVERLAP AN ACCESSIBLE ROUTE AND SHALL NOT
<br />60" MIN. 60" MIN.
<br />I-_ J A DOOR IS PROVIDED WITH A CLOSER
<br />EXTEND INTO THE KNEE AND TOE SPACE UNDERNEATH THE LAVATORY MORE THAN 19". THIS CLEAR SPACE
<br />SIDE DOOR SIDE DOOR
<br />6. THE FOLLOWING PROVISIONS SHALL APPLY TO SWINGING DOORS INSTALLED IN A SERIES:
<br />FIXED OR BUILT-IN SEATING , TABLES AND COUNTERS SHALL COMPLY WITH CBC SECTIONS 1127A.12 AND 1122B.
<br />WHERE FIXED OR BUILT-IN SEATING, TABLES OR COUNTERS ARE PROVIDED IN ACCESSIBLE PUBLIC USE OR COMMON USE
<br />36" MIN. 60" MIN. FINISH TO FINISH CLEAR
<br />FINISH TO FINISH CLEAR
<br />SHALL COMPLY WITH ALLOWABLE REACH RANGES. 17" MIN.
<br />VANITY COUNTER WITH 25" MAX. LAVATORY
<br />MANEUVERING MANEUVERING
<br />34" 18" 34" MIN 2"�
<br />t�
<br />/
<br />AREAS, 5 PERCENT, BUT NEVER LESS THAN ONE, SHALL BE ACCESSIBLE AS FOLLOWS:
<br />A. ACCESSIBLE ROUTE OF TRAVEL. A ROUTE OF TRAVEL SHALL LEAD TO AND THROUGH SUCH FIXED OR BUILT-IN
<br />SHOWER SIDE CONTROL WALL ELEVATION FOR FIGURES 16.2 BACK CONTROL WALL
<br />BUILT-IN LAVATORY SHOWN FIXTURE
<br />'
<br />CLEAR CLR CLEAR CL I
<br />_/
<br />+ +
<br />SEATING AREAS OR TABLES.
<br />61/2" MAX. BOWL DEPTH SHOWN
<br />� �
<br />B. SEATING. IF SEATING SPACES FOR PERSONS IN WHEELCHAIRS ARE PROVIDED AT FIXED TABLES OR COUNTERS,
<br />CLEAR FLOOR SPACE SHALL BE PROVIDED PER DETAIL 22 ON THIS SHEET. SUCH CLEAR FLOOR SPACE SHALL NOT
<br />I
<br />.< � I i
<br />�____ RIM I COUNTER
<br />I
<br />v � W f
<br />p " a I I I o " Q I
<br />`\`I
<br />w J v J
<br />♦
<br />OVERLAP KNEE SPACE BY MORE THAN 19".
<br />60" MIN. FINISH TO FINISH CLEAR J _J I 1
<br />KNE
<br />I ♦ KNEE
<br />o w `� o w `U
<br />�� Q�
<br />C. KNEE CLEARANCE. WHEN SEATING SPACES FOR PERSONS IN WHEELCHAIRS ARE PROVIDED AT FIXED TABLES OR
<br />U 3 I 1 _J
<br />= C� _ _ Q
<br />,,,I
<br />I t
<br />� / 1 I
<br />=� � 1 i z> � ,��
<br />� ,1 I 1 U
<br />G�'�i
<br />COUNTERS, KNEE SPACES AT LEAST 27"HIGH SHALL COMPLY WITH THE FOLLOWING FIGURES:
<br />19" 48" MIN. 0" MIN.
<br />MA . CLEAR LEAR
<br />42"CLR. �30" CLR.L C
<br />1
<br />BACK WALL � W o w w
<br />1 112" MAX. 3" MAX. COMPARTMENT M o w I o 65 I
<br />t-w I
<br />- I
<br />_ 0
<br />OPENING = - I% MAXIMUM
<br />MAXI "' U' I 1
<br />I x Q w 6
<br />u M � o
<br />-
<br />I I �
<br />x M U I
<br />z I .< z TOE z
<br />w �,
<br />z
<br />� 1 i 1 v �/ 1
<br />L___
<br />y 59"MIN. AT y y 36" MIN. y 59"MIN. AT y
<br />DOOR PERMITTED
<br />G. MAXIMUM EFFORT TO OPERATE DOORS SHALL NOT EXCEED 8112 POUNDS FOR EXTERIOR DOORS AND 5 POUNDS FOR
<br />INTERIOR DOORS, SUCH PULL OR PUSH EFFORT BEING APPLIED AT RIGHT ANGLES TO HINGED DOORS AND AT THE
<br />F_____, I
<br />z i , « 1 I \\ / 1 �
<br />+
<br />,Q Q i 1/4" : 1'-0" SLOPE
<br />1/4" : 1'-0' L PE w I
<br />� J w 1
<br />z ,n
<br />1/2" MAX.
<br />�
<br />1 1 = ----�
<br />LO I i � 1 r �- z
<br />N �
<br />_ F.F.
<br />FLR. MTD. W.C. TO SWING OVER WHEN DR. FLR. MTD. W.C.
<br />OR 56" MIN. AT SWINGS IN OR 56" MIN. AT
<br />HATCHED PORTION
<br />WALL MTD. W.C. OF MANEUVERING WALL MTD. W.C.
<br />CENTER PLANE OF SLIDING OR FOLDING DOORS. COMPENSATING DEVICES OR AUTOMATIC DOOR OPERATORS MAYBE
<br />UTILIZED TO MEET THESE STANDARDS. WHEN FIRE DOORS ARE REQUIRED, THE MAXIMUM EFFORT TO OPERATE THE
<br />DOOR MAY BE INCREASED TO THE MINIMUM ALLOWABLE BY THE APPROPRIATE ENDORSEMENT AGENCY, NOT TO
<br />EXCEED 15 POUNDS.
<br />� =
<br />o - 1 1 z
<br />�' - --\ / \
<br />= U_ Z ______ w _______
<br />M o o 0 1l THRESHOLD
<br />5"MIN. 5"MIN. "MIN
<br />CLR. FLR. SPACE SPACE CLR. FLR. SPACE
<br />FIGURE 8.2-A FIGURE 8.2-B
<br />H. IF THE DOOR HAS A CLOSURE, THEN THE SWEEP PERIOD OF THE CLOSER SHALL BE ADJUSTED SO THAT FROM AN OPEN
<br />1 � 1 0
<br />� 0 I -1 1 I Of p
<br />INSULATE
<br />ACCESSIBLE COMPARTMENT WITH ACCESSIBLE COMPARTMENT WITH
<br />POSITION OF 70 DEGREES, THE DOOR WILL TAKE AT LEAST 3 SECONDS TO MOVE TO A POINT 3 INCHES FROM THE
<br />�_
<br />= w FOLDING I FOLDING 1Q o
<br />-----y -_-_-_ _ _ _ _ _ _ _ _ _ _ _ _ - -= y _ _
<br />r - - - -
<br />rn o I w o
<br />SEAT i i SEAT o
<br />t _______1 1. _ /I z CD C OPTIONAL
<br />18 MIN. 11"MIN PLUMBING
<br />PIPES
<br />C. THE FLOOR FINISH BENEATH THE LAVATORY SHALL EXTEND TO THE WALL.
<br />SIDE OUT SWING DOOR SIDE IN -SWING DOOR
<br />44"
<br />LATCH, MEASURED TO THE LANDING EDGE OF THE DOOR.
<br />I. THE TYPE OF LATCH AND LOCK FOR ALL DOORS SHALL BE IN ACCORDANCE WITH CBC SECTION 1008.
<br />J. HAND -ACTIVATED DOOR LATCHING, LOCKING AND OPENING HARDWARE SHALL BE CENTERED BETWEEN 30" AND 44"
<br />___ _
<br />- - - - - - - - - - - - - - - - ' ' - - - - - -1__ - __
<br />M z ENCLOSURE
<br />¢ w
<br />D. HOT WATER &DRAIN PIPES EXPOSED UNDER LAVATORIES SHALL BE INSULATED OR OTHERWISE COVERED.
<br />MIN. CLR.
<br />ABOVE THE FLOOR. LATCHING AND LOCKING DOORS THAT ARE HAND ACTIVATED AND ON AN ACCESSIBLE ROUTE
<br />SHALL BE OPERABLE WITH A SINGLE EFFORT BY LEVER TYPE HARDWARE, PANIC BARS, PUSH PULL ACTIVATING BARS
<br />WHEELCHAIR SEATING SPACE WHEELCHAIR TABLE SPACE
<br />M
<br />FRONT 1/2" MAX. N o
<br />THERE SHALL BE NO SHARP OR ABRASIVE SURFACES UNDER LAVATORIES.
<br />E. LAVATORY FAUCET CONTROLS AND OPERATION MECHANISMS SHALL BE OPERABLE WITH ONE HAND AND
<br />r---- _ GRAB BARS:
<br />z 1 1
<br />OR OTHER HARDWARE DESIGNED TO PROVIDE PASSAGE WITHOUT REQUIRING THE ABILITY TO GRASP THE HARDWARE.
<br />KNEE SPACE IS NOT REQUIRED AT CHECKOUT COUNTERS OR SERVICE COUNTERS.
<br />SEAT WALL THRESHOLD CN
<br />N
<br />SHALL NOT REQUIRE TIGHT GRASPING, PINCHING OR TWISTING OF THE WRIST. THE FORCE TO ACTIVATE
<br />�
<br />- � 1 36" x 48" 1 M SHALL BE INSTALLED IN
<br />J � �
<br />"' CLR. - ACCORDANCE WITH DETAILS 10
<br />LOCKED EXIT DOORS SHALL OPERATE CONSISTENT WITH NOTE H ABOVE, IN THE DIRECTION OF EGRESS
<br />K. LEVER OR LEVER ACTUATED LATCHES OR LOCKS SHALL BE CURVED TO RETURN TO WITHIN 112" OF THE DOOR TO
<br />24"MIN. 36"MIN. OPENING
<br />CONTROLS SHALL BE NO GREATER THAN 5 POUND -FORCE. LEVER OPERATED, PUSH -TYPE, AND
<br />M 1 1 M M
<br />PREVENT CATCHING OF CLOTHING OF PERSONS DURING EGRESS.
<br />D. HEIGHT OF WORK SURFACES. THE TOPS OF TABLES AND COUNTERS SHALL BE 28" TO 34" FROM THE FLOOR TO THE
<br />ELECTRONICALLY CONTROLLED MECHANISMS ARE EXAMPLES OF ACCEPTABLE DESIGNS. SELF -CLOSING
<br />�- -- AND 12 OF THIS SHEET.
<br />L. THE BOTTOM 10" OF ALL DOORS AND/OR GATES SHALL HAVE A SMOOTH, UNINTERRUPTED SURFACE TO ALLOW THE
<br />GROUND.
<br />VALVES ARE ALLOWED IF THE FAUCET REMAINS OPEN FOR AT LEAST 10 SECONDS.
<br />60" MIN.
<br />DOOR TO BE OPENED BY A WHEELCHAIR FOOTREST WITHOUT CREATING A TRAP OR HAZARDOUS CONDITION. WHERE
<br />FIGURE 16.2 ALTERNATE ROLL -IN SHOWER, PLAN VIEW ALTERNATE FIGURE 16.3 ALTERNATE ROLL -IN SHOWER
<br />F. WHERE MIRRORS OR TOWEL FIXTURES ARE PROVIDED, AT LEAST ONE OF EACH SHALL BE ACCESSIBLE AND
<br />FIGURE 8.3
<br />NARROW FRAME DOORS ARE USED, A 10" HIGH SMOOTH PANEL SHALL BE INSTALLED ON THE PUSH SIDE OF THE DOOR.
<br />SHOWER SEAT WITH OPTIONAL ENCLOSURE, PLAN VIEW
<br />SHALL BE MOUNTED WITH THE BOTTOM EDGE NO HIGHER THAN 40" FROM THE FLOOR. SEE DETAIL14 ON THIS
<br />AMBULATORY ACCESSIBLE COMPARTMENT WITH FRONT OUT -SWING DOOR
<br />SHEET FOR ADDITIONAL INFORMATION.
<br />STORAGE & BUILT-INS
<br />24
<br />SHOWER
<br />16
<br />LAVATORY
<br />12
<br />TOILET COMPARTMENTS
<br />8
<br />DOORS
<br />4
<br />Architecture + Planning
<br />17911 Von Karman Ave.
<br />Suite 200
<br />Irvine, CA 92614
<br />ktgy.com
<br />949.851.2133
<br />KTGY Project No: 2017-0934
<br />Project Contact: Debbie Holland
<br />Email: dholland@ktgy.com
<br />Principal: Wil Wong
<br />Project Designer: D. Schoolmeester
<br />Project Director: Debbie Holland
<br />Developer
<br />ED OAK
<br />INVlipS'I'I'�•'L��N I'S
<br />4199 CAMPUS DRIVE
<br />IRVINE, CA 92612
<br />PHONE NO. (714) 342-2502
<br />ff
<br />O
<br />0
<br />Z
<br />Q
<br />2
<br />H
<br />r
<br />O
<br />Q
<br />U
<br />Q
<br />z
<br />Q
<br />Q
<br />z
<br />Q
<br />W
<br />I.-
<br />w
<br />w
<br />I-
<br />=
<br />I-
<br />w
<br />No. Date Description
<br />It is the clients responsibility prior to or during construction to notify the architect in writing
<br />of any perceived errors or omissions in the plans and specifications of which a contractor
<br />thoroughly knowledgeable with the building codes and methods of construction should
<br />reasonably be aware. Written instructions addressing such perceived errors or omissions
<br />shall be received from the architect prior to the client or clients subcontractors proceeding
<br />with the work. The client will be responsible for any defects in construction if these
<br />procedures are not followed.
<br />, ARcN�TF
<br />\, �� ��
<br />��
<br />� No. C29795 �
<br />RENEWAL DATE
<br />AUGUST 31, 2023
<br />F of CA_\1
<br />License Stamp
<br />COMMON & PUBLIC
<br />AREA ACCESSIBILITY
<br />NOTES & DETAILS
<br />AD-02
<br />J
<br />C�
<br />MG
<br />W
<br />�D
<br />v J
<br />U
<br />�..�..�
<br />=
<br />U
<br />z
<br />^J
<br />0-
<br />F___
<br />V /
<br />ILL
<br />N
<br />C)
<br />CN
<br />r
<br />C)
<br />C)
<br />COPYRIGHT C
<br />
|